Emerson Rosemount 5900S Series Reference Manual Download

Page: 236 / 298

Figure A-4: Dimensions of Rosemount 5900S with Still-Pipe Array Antenna

226 (8.9)

290 (11.4)

224 (9.6)

177 (7.0)

Dimensions are in millimeters (inches).

Table A-4: Available sizes for Still-Pipe Array Antenna

Antenna diameter (D)

B (mm)

5 in. / DN125 (Ø 120 mm)

6 in. / DN150 (Ø 145 mm)

8 in. / DN200 (Ø 189 mm)

10 in. / DN250 (Ø 243 mm)

12 in. / DN300 (Ø 293 mm)

Specifications and reference data

Reference Manual

September 2019

00809-0100-5900

236

Reference Manual

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands

Emerson Rosemount 5900S Series, Reference Manual

Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands