manualshive.com logo in svg

Emerson Rosemount 5900S Series, Reference Manual, Page: 92 / 298

Share
Download
Emerson Rosemount 5900S Series Reference Manual Download Page 92

Temperature Transmitter. Note that the Primary Tankbus is terminated in the Rosemount
5900S terminal block (X2).

Figure 3-31: Rosemount 5900S Wiring Diagram for 2-in-1 Version with two Tankbuses

 

A. Rosemount TankMaster PC

B. Rosemount 2410 Tank Hub

C. Field Communicator

D. Primary Tankbus in (gauge 1)

E. Power supply
F. Termination

G. Rosemount 2240S Multi-input Temperature Transmitter
H. Secondary Tankbus (gauge 2)

I. Rosemount 5900S Radar Level Gauge (2-in-1)

See also 

Terminal blocks

 for information on terminal block connections.

Figure 3-32

 illustrates the 2-in-1 version of the Rosemount 5900S with a single intrinsically

safe Tankbus. The Tankbus is connected to the first level gauge via terminal X1, and to the
second level gauge via jumpers between terminals X3 (Primary Tankbus out) and X4
(Secondary Tankbus in).

Tankbus termination is enabled in the Rosemount 5900S terminal block (X2).

Installation

Reference Manual

September 2019

00809-0100-5900

92

Reference Manual

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Reviews:

No comments