Emerson Rosemount 5900S Series Reference Manual Download | Manualshive

Page: 151 / 298

background image

3. Device Error

4. Internal Communication Failure

5. Electronics Failure

FD_FAIL_MASK

This parameter will mask any of the failed conditions listed in FD_FAIL_MAP. A bit on
means that the condition is masked out from alarming and being broadcast to the host
through the alarm parameter.

FD_FAIL_PRI

Designates the alarming priority of the FD_FAIL_ALM, see

. The default is 0

and the recommended values are between 8 and 15.

FD_FAIL_ACTIVE

This parameter displays which of the conditions is active.

FD_FAIL_ALM

Alarm indicating a condition within a device which makes the device non-operational.

Out of specification alerts

An Out of Specification alert indicates that the device operates out of the specified
measurement range. If the condition is ignored, the device will eventually fail. There are
five parameters associated with Out of Specification alerts, they are described below.

FD_OFFSPEC_MAP

The FD_OFFSPEC_MAP parameter contains a list of conditions indicating that the device or
some part of the device operates out of specification. Below is a list of the conditions with
the highest priority first. This priority is not the same as the FD_OFFSPEC_PRI parameter
described below. It is hard coded within the device and is not user configurable.

Below is a list of the conditions

1. Device Major Information

2. Device Warning

FD_OFFSPEC_MASK

The FD_OFFSPEC_MASK parameter will mask any of the failed conditions listed in
FD_OFFSPEC_MAP. A bit on means that the condition is masked out from alarming and
being broadcast to the host through the alarm parameter.

FD_OFFSPEC_PRI

This parameter designates the alarming priority of the FD_OFFSPEC_ALM, see

. The default is 0 and the recommended values are 3 to 7.

FD_OFFSPEC_ACTIVE

The FD_OFFSPEC_ACTIVE parameter displays which of the conditions is detected as active.

(12)

Note that Out of Specification alerts are not enabled by default.

Reference Manual

Configuration

00809-0100-5900

September 2019

Rosemount 5900S Radar Level Gauge

151

«
...
149
150
151
152
153
...
»

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Reviews:

No comments

Related manuals for Rosemount 5900S Series

7-10-30LP8 UP-KIT

Brand: M2 Antenna Systems Pages: 6

Brand: Naval Pages: 2

BAS-6103 Venus UHF

Brand: BAS Pages: 3

Brand: Kathrein Pages: 52

Brand: Hirschmann Pages: 2

Brand: KVH Industries Pages: 46

Super Hi-Q Loop

Brand: MFJ Pages: 14

Brand: Jegs Pages: 4

Brand: DirecTV Pages: 1

Brand: APLIC Pages: 20

303340/20191008DG006

Brand: APLIC Pages: 24

Brand: Televes Pages: 16

Brand: Encore Pages: 2

Brand: PRO.SIS.TEL. Pages: 6

Brand: SABINE Pages: 60

Brand: Raymarine Pages: 36

Brand: Steren Pages: 2

Brand: M2 Antenna Systems Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands