Emerson Rosemount 5900S Series Page 66 Reference Manual Download

Page: 66 / 298

3.3.4

Array antenna - hinged hatch

Prerequisites

See

Still Pipe antenna requirements

for information on mounting considerations before

installing the gauge on the tank.

Follow this instruction when installing the Rosemount 5900S with Array Antenna Hinged
Hatch version.

Procedure

1. Mount the hatch on the nozzle. The hatch has a welded flange with a hole pattern

that fits the nozzle flange.

A. Gasket

2. Tighten the flange screws. The smaller hatches may have a couple of pin bolts in

addition to the screws.

Installation

Reference Manual

September 2019

00809-0100-5900

Reference Manual

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands

Emerson Rosemount 5900S Series, Reference Manual

Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands