Emerson Rosemount 5900S Series Reference Manual Download

Page: 59 / 298

11. Align the level gauge by using the cross hairs on top of the transmitter head.

In case the weather protection hood is attached, the gauge can be aligned by using
a line of sight along the screws on top of the head.

A. Tank

B. Tank center

C. Line of sight

12. Ensure that the gauge is directed at an angle of 45° to the line of sight from the

center of the tank to the wall.

Reference Manual

Installation

00809-0100-5900

September 2019

Rosemount 5900S Radar Level Gauge

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands

Emerson Rosemount 5900S Series, Reference Manual

Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands