Emerson Rosemount 5900S Series Page 249 Reference Manual Download

Page: 249 / 298

A.14.4

Rosemount 5900S Radar Level Gauge with LPG/LNG
antenna

Table A-9: Rosemount 5900S Radar Level Gauge with LPG/LNG Antenna Ordering Information

Model

Product Description

5900S

Radar Level Gauge

Performance class

Premium: ±0.5 mm (0.020 in.) instrument accuracy

Safety certification (SIS)

(1)

Certified IEC 61508 SIL 3 capable

(2)

Certified IEC 61508 SIL 2 capable

None. Ready for upgrade to Safety certification (SIS)

None

Redundancy

2-in-1: Dual independent radar level gauge electronics

None. Ready for upgrade to 2-in-1

None. Single radar level gauge electronics

Tankbus: Power and communication

Bus powered 2-wire F

OUNDATION

™

Fieldbus (IEC 61158)

Hazardous location certification

ATEX Intrinsic Safety

IECEx Intrinsic Safety

FM-US Intrinsic Safety

FM-Canada Intrinsic Safety

INMETRO Intrinsic Safety (Brazil)

(3)

KC Intrinsic Safety (South Korea)

CCOE/PESO Intrinsic Safety (India)

(4)

Japan Intrinsic Safety

Technical Regulations Customs Union (EAC) Intrinsic Safety

None

Custody transfer type approval

(5)

(6)(7)

OIML R85 edition 2008

CMI (Czech Republic)

NMI (Australia)

PTB Eich (Germany)

TJA (Estonia)

Reference Manual

Specifications and reference data

00809-0100-5900

September 2019

Rosemount 5900S Radar Level Gauge

249

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands

Emerson Rosemount 5900S Series, Reference Manual

Search results

Summary of Contents for Rosemount 5900S Series

Reviews:

Related manuals for Rosemount 5900S Series

Brands by name

Popular brands