Antenna Installation
& Connections
Diagram
BAS
-
6103 Venus UHF
QUICK USER GUIDE | ПАСПОРТ
TV Antenna Outdoor
Omnidirectional
for Vehicles
1
3
5
2
4
6
Features
:
-
Compatible with HDTV
(
DVB-T, DVB-T2, ATSC, ISDB-T
,
FreeTV, etc.).
-
Built-in high-gain low-noise ampli er, shielded to eliminate interference.
-
Omnidirectional antenna receives UHF TV-signal from every direction regardless on where
you are traveling.
-
Ampli er with SMD technology and micro-electronics ensure excellent antenna performance.
-
Built-in ltering of signals 2G, 3G, LTE,
WiFi
and other radio-frequency interference.
-
Waterproof antenna made of UV resistant ABS material
-
Receiving range of TV signal up to 80 miles
Technical Speci cations:
UHF — 470..790MHz
Gain — 30dB
Direction — omnidirectional
Power Supply — DC 1
1
..
28
V 100mA
Size — 320x320x165mm
Weight — 0.850kg
In Box:
Antenna (with cable) — 1pcs
Mount Stand — 1pcs
Locking Nut — 1pcs
Sealing Cup — 1 pcs
Sealing Ring — 1pcs
Mounting Screw — 4pcs
F-F connector — 1pcs
Injector — 1pcs
User Guide — 1pcs
Installation:
Step 1: Decide location of power supply before mounting your antenna. Antenna and power
supply location will determine where and how you run the cables.
DO NOT install the antenna before you read this instruction.
Step 2: Drill a hole thru the roof to run cable from the antenna into your vehicle. Or if your
vehicle have a cable hole already, run the cable thru hole to the antenna.
Step 3: Using 4 screw to securely fasten antenna mount to the roof. Do not over tighten
the mounting bolts, damage to the mounting stand or
roof may occur.
Step 4: Use cable tool to drive the cable into the mounting bracket on the underside of the
antenna, aligning the end of the connector with the F connector
on the antenna.
Step 5: Slide antenna onto the mount. Gently pull back any extra cable inside vehicle.
Step 6: Fasten antenna to mount and tighten hex nut. Tighten rmly to prevent antenna
from turning on mount.
Step 7:
Route the coaxial cable
(Type RG-6/U, SAT-50, SAT-703 etc.)
inside the vehicle
.
Step 8:
Connect the coaxial cable to the antenna and to the power injector.
Step
9
: Connect power injector to supply –
red wire to positive power supply 11-28 Volts
DC,
black wire to ground or negative power supply.
Step 10
:
Connect coaxial cable from the power injector to TV set
.
Uninstalling the antenna and retaining the
antenna mount:
Step 1:
D
isconnect the coaxial cable from the injector
.
Step 2:
Loosen hex nut and
remove the antenna from the mount.
Step 3:
Gently pull an extra cable
out of the
vehicle
.
Step 4: Fasten the cup to mount and tighten hex nut.
Thank you for choosing the
antenna outdoor BAS-6103 Venus UHF
!
It has been
developed by a team of engineers determined to continue the
tradition
of excellence
and innovation of REMO-
Technologii
products. The
antenna BAS-6103 Venus
UHF
is made of high-quality materials
in
accordance with thoroughly
detailed design.
Vehicle Roof
F-connector
Mounting Screw
Mounting Stand
Sealing Cup
Antenna
Locking Nut
Coaxial Cable
F-connector
Black Wire
- Ground
Red Wire
- 12..24V DC
F-F connector
F-connector (for USA)
TV-plug (for EU and
other
countries
)
Coaxial Cable
Injector
Purchased
Separately
F-connector
to TV-set
Sealing Ring
Set the template
Remove the template
Fasten antenna mount
to the roof
Check the presence
of the sealing ring!
Installation
Antenna
Mount Diagram
REMO-Technologii
,
LLC., P.O.Box 500, Saratov, 410052, Russia
www.remo-electronics.com
,
+7 (8452) 495-232, 495-24
2
