Dell Brocade 825 Installation And Reference Manual Download Page 93

Page: 93 / 272

Brocade Adapters Installation and Reference Manual

53-1002144-01

Chapter

Software Installation

In this chapter

•

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

•

Installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

•

Using the Brocade Adapter Software Installer. . . . . . . . . . . . . . . . . . . . . . . . 68

•

Using software installation scripts and system commands . . . . . . . . . . . . . 89

•

Confirming driver package installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

•

Verifying adapter installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

•

Updating drivers with HCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

•

Installing HCM to a host from the HCM Agent . . . . . . . . . . . . . . . . . . . . . . . 112

•

HCM Agent operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

•

HCM configuration data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

•

Setting IP address and subnet mask on CNAs . . . . . . . . . . . . . . . . . . . . . . 115

Introduction

This chapter provides procedures to install the adapter driver, HCM, and other software using the
following options:

•

“Using the Brocade Adapter Software Installer”

on page 68.

•

“Using software installation scripts and system commands”

on page 89.

Procedures are also provided for removing software using the Brocade Adapter Software
Uninstaller (refer to

“Software removal using Adapter Software Uninstaller”

on page 83), and

upgrading software using the Brocade Adapter Software Installer (refer to

“Software upgrade using

Adapter Software Installer”

on page 87). Procedures are also provided for configuring HCM agent

operations, and setting the IP address and subnet mask on CNAs and Fabric Adapter ports
configured in CNA or NIC mode.

To troubleshoot problems after installation, refer to the

Brocade Adapters Troubleshooting Guide

To keep adapter drivers and boot code synchronized, be sure to update your adapter with the latest
boot image whenever you install or update adapter driver packages. Use the following steps:

1. Go to the adapters website at

www.brocade.com/adapters

2. Navigate to the Downloads page.

3. Select your operating system from the Downloads list or download the ISO image.

4. Download the boot image file from the “Boot Code” section.

5. Refer to

“Boot code updates”

on page 118 for instructions to install the image.

Summary of Contents for Brocade 825

















































































































































































































































































Search results

Summary of Contents for Brocade 825

Reviews:

Brands by name

Popular brands

Dell Brocade 825, Installation And Reference Manual

Search results

Summary of Contents for Brocade 825

Reviews:

Brands by name

Popular brands