manualshive.com logo in svg

Dell Brocade 825, Installation And Reference Manual

Share
Download
Dell Brocade 825 Installation And Reference Manual Download Page 164

136

Brocade Adapters Installation and Reference Manual

53-1002144-01

Boot over SAN

4

Configuring BIOS using the Brocade configuration utility

NOTE

“Brocade BIOS configuration utility” and “Brocade BIOS configuration menu” are used 
interchangeably in this manual.

The Brocade BIOS Configuration Utility allows you to perform the following operations on selected 
adapters:

•

Enable or disable BIOS to support boot over SAN.

-

You must enable BIOS to support boot over SAN for an adapter port. If disabled, the host 
system cannot boot from Fibre Channel disk drives.

-

The default setting for the adapter boot BIOS is 

BIOS is enabled with Fabric Discovered

 on 

all adapter ports. 

•

Enable one of the following Boot Options: 

NOTE

For booting from direct-attached Fibre Channel targets, select the Flash Values or First LUN 
options.

-

Fabric Discovered
Host boots from LUN information provided by the fabric.

NOTE

Fabric-based boot LUN discovery (Fabric Discovered) is not supported for booting from 
direct-attached targets.

-

Flash Values
Host boots from LUN information stored in flash memory.

-

First LUN
Host boots from the first visible LUN.

•

Set port speed for the adapter (HBAs and Fabric Adapter ports configured in HBA mode only).

•

Select boot LUNs from discovered targets.

•

Review adapter properties, such as the following:

-

Port speed

-

PWWN

-

NWWN

-

BIOS version

To configure BIOS parameters using the Brocade BIOS Configuration Utility, use the following steps.

1. Power on the host system.

2. Watch the screen as the system boots. When “Brocade BIOS configuration utility” displays, 

press 

Alt

+

B

 or 

Ctr

l+

B

.

The Brocade BIOS Configuration Menu displays a list of installed adapter ports, similar to the 
following. 

Summary of Contents for Brocade 825

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands