manualshive.com logo in svg

Dell Brocade 825, Installation And Reference Manual

Share
Download
Dell Brocade 825 Installation And Reference Manual Download Page 137

Brocade Adapters Installation and Reference Manual

109

53-1002144-01

Installing SNMP subagent

3

•

Make sure that all Fibre Channel devices connected through the adapter and associated FCoE 
or Fibre Channel switch are correctly connected, powered up, and operating correctly. If not 
powered up, devices will be unavailable.

•

Verify host system storage, switch, and operating system compatibility using the 
interoperability matrices on the Brocade adapters website at 

www.brocade.com/adapters

. 

•

Verify the following for stand-up adapters only:

-

Observe LED operation on adapter and refer to the 

“Adapter LED operation”

 on page 177 

for Fabric Adapters, 

“Adapter LED operation (stand-up adapters)”

 on page 191 for CNAs, 

and 

“Adapter LED operation (stand-up adapters)”

 on page 184 for HBAs. LEDs are visible 

through the adapter’s mounting bracket.
If LEDs indicate that the link between the adapter and switch is not operational, this could 
mean that a problem on the link between the switch and adapter or that the driver is not 
loaded and communicating with the switch.

-

The adapter is installed in the appropriate connector in the host system.

-

All small form factor pluggable (SFP) optic receivers are correctly installed, seated, and 
latched in adapter SFP receiver slots.

-

Cables are properly connected to the appropriate adapter port and seated in the SFP 
connector.

-

Correct options are configured for the slot where the adapter is installed,

•

Verify the following for mezzanine adapters only:

-

The blade server or server blade is turned on.

-

The adapter is installed in the appropriate connector. On some blade servers or server 
blades, connectors may only support a specific adapter type. Refer to your blade sever 
documentation for help. 

-

Whether the blade server or server blade on which the adapter is installed is correctly 
configured and installed in the blade system enclosure. Refer to your blade server and 
blade system enclosure documentation for help.

-

Any modules or blades in that support adapter operation are installed in the appropriate 
enclosure bays and correctly configured. Refer to the documentation for your blade system 
enclosure for help. 

-

The blade system enclosure is configured for adapter operation. Refer to your blade 
system enclosure and documentation for blade system enclosure components for help. 

-

You are using the latest device drivers, firmware, and BIOS for the blade server (or server 
blade) and other components in the blade system enclosure that support adapter 
operation.

Installing SNMP subagent

Simple Network Management Protocol (SNMP) is supported by CNAs and by Fabric Adapters for 
ports configured in CNA or NIC mode. For more information, refer to 

“Simple Network Management 

Protocol”

 on page 34. Brocade adapter SNMP is supported through an extension to the SNMP 

master agent, called the subagent, which processes SNMP queries for Brocade adapters. The 
subagent is only supported on Linux and Windows systems. SNMP subagent files are copied to 
your host system when you install adapter management utilities through HCM and the Brocade 
Adapter Software Installer (BASI).

Summary of Contents for Brocade 825

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands