manualshive.com logo in svg

Dell Brocade 825, Installation And Reference Manual

Share
Download
Dell Brocade 825 Installation And Reference Manual Download Page 146

118

Brocade Adapters Installation and Reference Manual

53-1002144-01

Boot code updates

4

A single, updatable boot code image, stored in the adapter option read-only memory (option ROM) 
memory, contains all boot code for supported host platforms. 

NOTE

By default, BIOS and UEFI are enabled on adapter ports for booting over SAN.

Boot code updates

The adapter boot code contains the following:

•

PCI BIOS 2.1 or later, PCI firmware 3.0
Boot code for PCI system

•

BIOS 
Boot code for x86 and x64 platforms

•

Unified Extensible Firmware Interface (UEFI)
Boot code for UEFI systems

NOTE

UEFI is not supported on the Brocade 804 adapter.

•

Adapter firmware 

Update the adapter with the latest boot code image for installed Brocade adapters from the 
Brocade adapters website at 

using 

the following steps. 

1. Go to the adapters website at 

www.brocade.com/adapters

. 

2. Navigate to the adapters Downloads page. 

3. Select your operating system from the Downloads list to display appropriate download files.

4. Download the boot code image from the “Boot Code” area.

Update the boot code image file to the adapter installed on your host system using the Host 
Connectivity Manager (HCM) and BCU commands. Although BCU updates the file from the host’s 
local drive, you can use HCM to update from a remote system. 

NOTE

All Brocade adapters installed in a host system must use the same boot code version.

NOTE

To keep drivers and boot code synchronized, be sure to update your adapter with the latest boot 
image 

after

 you install or update adapter driver packages. Be sure to update drivers before updating 

the boot code.

You can determine the current BIOS version installed on your adapter using the following methods:

•

Viewing the BIOS that displays on your system screen during hardware reinitialization, just 
before you are prompted to press Ctrl and B or Alt and B to enter the Brocade adapter 
Configuration Utility. 

•

Entering the bcu adapter --query command. The installed BIOS version displays in the Flash 
Information section of the command output. 

Summary of Contents for Brocade 825

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands