manualshive.com logo in svg

Dell Brocade 825, Installation And Reference Manual

Share
Download
Dell Brocade 825 Installation And Reference Manual Download Page 115

Brocade Adapters Installation and Reference Manual

87

53-1002144-01

Using the Brocade Adapter Software Installer

3

•

To remove HCM only without using silent mode, but with debug messages.
Windows systems

Uninstall.bat -DCHOSEN_INSTALL_SET=GUI -DEBUG=true

Linux or Solaris systems

sh Uninstall.sh -DCHOSEN_INSTALL_SET=GUI -DEBUG=true

Software upgrade using Adapter Software Installer

To upgrade HCM, adapter driver packages, or the driver packages and HCM, simply follow the 
instructions under 

“Using the GUI-based installer”

 on page 69 or 

“Software installation using 

Software Installer commands”

 on page 76. You do not need to remove the existing software first. 

However, refer to the following important notes when upgrading, as procedures may vary from 
first-time installation on specific operating systems.

•

Windows systems

-

When upgrading the driver for Windows systems, you do not need to reboot after 
installation.

-

The recommended procedure for upgrading Windows drivers is to install the new driver 
without first removing the existing driver.

-

When using the Brocade Adapter Software Installer commands for installation and an 
existing driver is installed on the system, you must use the following parameter to 
overwrite with the new driver.

-DFORCE_WIN_DRIVER_INSTALLATION=1 

For example, to overwrite the existing driver packages with the new driver packages and 
start the HCM Agent automatically, use the following command.

brocade_adapter_software_installer_windows_<platform>_<version>.exe 

-DCHOSEN_INSTALL_SET=DRIVER -DFORCE_WIN_DRIVER_INSTALLATION=1 -i silent 

For example, to overwrite the existing drivers with the new drivers, use the following 
command.

brocade_adapter_software_installer_windows_<platform>_<version>.exe 

-DCHOSEN_INSTALL_SET=BOTH -DFORCE_WIN_DRIVER_INSTALLATION=1 -i silent 

-

If VLAN configurations exist (CNAs and Fabric Adapter ports configured in CNA mode), a 
backup message displays during upgrade or reinstallation of drivers. This message will 
note the location where configurations were stored. You can restore these configurations 
after installation completes.

•

Linux systems
When upgrading the driver for Linux systems, you do not need to reboot the host system after 
installation. 

•

Solaris systems
When upgrading the driver for Solaris systems, you must reboot the host system. The new 
driver is effective after system reboot.

Summary of Contents for Brocade 825

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands