manualshive.com logo in svg

Dell Brocade 825, Installation And Reference Manual

Share
Download
Dell Brocade 825 Installation And Reference Manual Download Page 190

162

Brocade Adapters Installation and Reference Manual

53-1002144-01

Boot over SAN

4

The driver loads to the system.

If the driver update was successful, a “Driver Update OK” or similar message displays:

10. Press Enter.

11. If the system prompts you to update another driver, select BACK, then press Enter. 

12. When prompted to insert the SLES 11 product CD #1, insert the CD into the drive and select 

OK.

13. Continue responding to on-screen instructions and refer to your system documentation as 

necessary to format and complete installation on the target boot LUN.

After SLES installs on the remote LUN, the system should automatically reboot from the LUN.

Installing the full driver package on boot LUNs

The preceding procedures for each operating system under 

“Operating system and driver 

installation on boot LUNs”

 on page 148, do not install the HCM Agent and the full range of Brocade 

Command Line Utilities. To install the full driver package with adapter agent and all BCU 
commands, including bfa_supportsave, perform these additional steps.

NOTE

For information available driver packages and operating system support for drivers, refer to 

“Software installation and driver packages”

 on page 43 and 

“Operating system support”

 on 

page 40.

1. Compare the version of the full driver package that you wish to install with the version of the 

driver already installed on the boot LUN. There are a variety of methods to determine the driver 
version installed on your operating system. Refer to 

“Confirming driver package installation”

 on 

page 103 for more information.

If the versions do not match, you will perform additional steps to initialize the new package on 
your system.

2. Install the full driver package using steps for your operating system under 

“Using the Brocade 

Adapter Software Installer”

 on page 68

•

If the driver that you install and the driver already installed on the LUN match, perform 
steps as normal to complete installation. You will be able to use the additional utilities and 
HCM Agent installed with the full package.
For Linux systems, install the latest version of brocade_driver_linux_<version>.tar.gz using 
instructions under 

“Driver installation and removal on Linux systems”

 on page 95. This will 

install all package utilities without updating the driver. You do not need to reboot the 
system.

•

If the driver that you install and the driver already installed on the LUN do not match, go on 
to 

step 3

. 

3. If the version of the driver installed on the boot LUN and the driver you are installing do not 

match, perform these additional steps for your operating system:

Windows

Reboot the system to initialize the new driver.

Summary of Contents for Brocade 825

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands