Dell Brocade 825 Installation And Reference Manual Download Page 127

Page: 127 / 272

Brocade Adapters Installation and Reference Manual

53-1002144-01

Using software installation scripts and system commands

8. When a driver is installed and the host system is connected to the fabric turn on host power

and verify adapter operation. Verify proper LED operation for stand-up adapters by referring to

“Adapter LED operation (stand-up adapters)”

on page 184.

Removing driver packages from Solaris systems

Use the following steps to remove driver and utility packages.

NOTE

Root access is required to remove the packages.

1. Log on to your system as root user.

2. Determine if the driver and utility packages are installed using the following commands:

# pkginfo|grep bfa

# pkginfo|grep bna

# pkginfo|grep brcd-util

3. Determine if the HCM Agent is running using procedures under

“HCM Agent operations”

page 112. If it is, stop the agent using steps under the same heading.

4. From any directory, enter the following commands to remove installed packages:

# pkgrm bfa

# pkgrm bna

# bkgrm brcd-util

5. Respond to prompts “Do you want to remove this package?” by entering y.

6. Respond to prompts “Do you want to continue with the removal of this package?” by entering y.

After a series of messages, the following confirms removal:

# Removal of <bfa> was successful.

# Removal of <bna> was successful.

# Removal of <brcd-util> was successful.

Upgrading driver on Solaris systems
To update driver packages, simply install new packages using steps under

“Installing driver

packages on Solaris systems”

on page 97.

NOTE

When upgrading the drivers for Solaris systems, you must reboot the host system. The new drivers
are not effective until after system reboot.

Driver installation and removal on VMware systems

Instructions are provided in this section to install adapter drivers on ESX and ESXi systems.

NOTE

Since the ESX 5,0 driver installation process does not enforce maintenance mode, it is
recommended that you put the host in maintenance mode, as since a system reboot is required
after installation.

Summary of Contents for Brocade 825

















































































































































































































































































Search results

Summary of Contents for Brocade 825

Reviews:

Brands by name

Popular brands

Dell Brocade 825, Installation And Reference Manual

Search results

Summary of Contents for Brocade 825

Reviews:

Brands by name

Popular brands