Danfoss VLT AQUA Drive FC 200, Instruction Manual

Page: 72 / 155

0-20 Display Line 1.1 Small
Option: Function:
[1639] Control Card Temp. Temperature of the control card.
[1650] External Reference Sum of the external reference as a
percentage, i.e., the sum of
analog/pulse/bus.
[1651] Pulse Reference
[1652] Feedback [Unit] Signal value in units from the
programmed digital input(s).
[1653] Digi Pot Reference View the contribution of the
digital potentiometer to the actual
reference Feedback.
[1660] Digital Input Displays the status of the digital
inputs. Signal low = 0; Signal high
= 1.
Regarding order, see
16-60 Digital
Input . Bit 0 is at the extreme right.
[1661] Terminal 53 Switch
Setting Setting of input terminal 53.
Current = 0; Voltage = 1.
[1662] Analog Input 53 Actual value at input 53 either as
a reference or protection value.
[1663] Terminal 54 Switch
Setting Setting of input terminal 54.
Current = 0; Voltage = 1.
[1664] Analog Input 54 Actual value at input 54 either as
reference or protection value.
[1665] Analog Output 42
[mA] Actual value at output 42 in mA.
Use
6-50 Terminal 42 Output to
select the variable to be
represented by output 42.
[1666] Digital Output [bin] Binary value of all digital outputs.
[1667] Freq. Input #29 [Hz] Actual value of the frequency
applied at terminal 29 as a pulse
input.
[1668] Freq. Input #33 [Hz] Actual value of the frequency
applied at terminal 33 as a pulse
input.
[1669] Pulse Output #27
[Hz] Actual value of pulses applied to
terminal 27 in digital output
mode.
[1670] Pulse Output #29
[Hz] Actual value of pulses applied to
terminal 29 in digital output
mode.
[1671] Relay Output [bin] View the setting of all relays.
[1672] Counter A View the present value of Counter
A.
[1673] Counter B View the present value of Counter
B.
0-20 Display Line 1.1 Small
Option: Function:
[1674] Prec. Stop Counter
[1675] Analog In X30/11 Actual value of the signal on input
X30/11 (General Purpose I/O Card.
Option)
[1676] Analog In X30/12 Actual value of the signal on input
X30/12 (General Purpose I/O Card.
Optional)
[1677] Analog Out X30/8
[mA] Actual value at output X30/8
(General Purpose I/O Card.
Optional) Use
6-60 Terminal X30/8
Output to select the variable to be
shown.
[1678]
[1679]
[1680]
Fieldbus CTW 1 Control word (CTW) received from
the bus master.
[1682] Fieldbus REF 1 Main reference value sent with
control word via the serial
communications network, e.g.,
from the BMS, PLC or other
master controller.
[1684] Comm. Option
Status Extended serial communication
option status word.
[1685] FC Port CTW 1 Control word (CTW) received from
the bus master.
[1686] FC Port REF 1 Status word (STW) sent to the bus
master.
[1690] Alarm Word One or more alarms in a Hex code
(used for serial communications)
[1691] Alarm word 2 One or more alarms in a Hex code
(used for serial communications)
[1692] Warning Word One or more warnings in a Hex
code (used for serial communi-
cations)
[1693] Warning word 2 One or more warnings in a Hex
code (used for serial communi-
cations)
[1694] Ext. Status Word One or more status conditions in
a Hex code (used for serial
communications)
[3401] PCD 1 Write to
MCO
[3402] PCD 2 Write to
MCO
[3403] PCD 3 Write to
MCO
How to program the adjustab... VLT AQUA 12-Pulse High Power Instruction Manual
MG.20.Y1.22 - VLT
®
is a registered Danfoss trademark 6-9
6 6