ComAp InteliDrive DCU Marine Manual Download

Page: 231 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

231

Related FW

3.0.0

Related applications

All

Comm object

Description

Intercontroller communication error.

OthrCommEr

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

Description

Charger fail detection. D+ output current is limited to cca 300 mA.

Guaranteed level for signal Charging OK = 90% of supply voltage.

There are three possible conditions for stop engine cranking:

Starting RPM, StartingPOil

and

D+ function

(when ENABLED). Starter goes off when any of these conditions becomes valid.

ChrgAlternFail

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

Description

Engine stop fail indication. Stop fail: engine does not reach 0 RPM after stop command within Engine

params: Stop time.

Stop Fail

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

779

Description

Engine overspeed indication.

Overspeed

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

Description

Under speed indication.

Underspeed

back to List of LBO

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands