ComAp InteliDrive DCU Marine Manual Download

Page: 15 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

2.1.3 Functions available from ID-DCU MARINE front panel keys

Function

Key combination

From where

Contrast increase

Enter + ↑

Main screen

Contrast decrease

Enter + ↓

Info screen

Enter + Page

LOC (Local) mode ON

Enter + Mode→ (Right)

LOC (Local) mode OFF

Enter + ←Mode (Left)

Fast edit

Enter hold for 4 sec.

Fault code reset

Fault reset

Alarm list

ECU fault code reset

Fault reset

ECU Alarm list

Requested speed increase

↑

Fast edit screen

Requested speed decrease

↓

Request confirmation and exit

Enter

active when Engine params:

EnLocalSpeed

= ENABLED

Exit without confirmation

Page

Backlight increase

Enter + ↑

Info screen

Backlight decrease

Enter + ↓

Go to Language screen

Page

Info screen exit

Automatic after 10 sec to Main

screen

Language selection

↑ or ↓

Language screen

Language screen exit

Enter

The system supports following character sets:

West European - Code page 1252 in Windows

East European - Code page 1250 in Windows

Russian - Code page 1251 in Windows

Turkish - Code page 1254 in Windows

Simplified Chinese - Code page 936 in Windows.

Note:

If the configuration table has a code page that is not supported in the display processor, “Unsupported

code page” message appears on the ID-DCU MARINE screen. Press

Page

to return back to Language

selection.

Note:

The Fast Edit function is available only in case of accessible parameter, i.e. if entered password level on

ID-DCU MARINE corresponds to protected level of parameter associated to Fast Edit function.

2.1.4 How to change controller language?

Go to Info screen by pressing

Page

Enter

. Press

Page

to go to Language screen. Select language ↑ or ↓ a

press Page to confirm selection and exit window.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands