ComAp InteliDrive DCU Marine Manual Download

Page: 11 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Memo1

Each time rising edge is detected with LBI: Memo1 Trigger

Memo2

Each time rising edge is detected with LBI: Memo2 Trigger

MomAvgFlCon L

Momentary average fuel consumption per nautical mile. Calculated from fuel

consumption and boat speed.

Result is not rounded, e.g. 9/100 is displayed as 0,0

If FuelConsumpt is 0 then MomAvgFlCon L is displayed as invalid value #####.

Note:

Statistic values can be adjusted from InteliMonitor, password 3 level protected by default.

Note:

Internal display does not support Unsigned Long values so it does not display correctly values higher

than 2,147,483,647. Could be roughly says that issue is connected with values having 10 digits and more.If

there is higher value, it treats it as Signed long and show it as negative with "-" (minus sign).Workaround: If

numbers with 10 digits has unlogically minus mark number should be recalculated.

History records

Following table does not contain Wrn, Sd and Fls messages from external units.

Events specification

Protection type

Information available on binary output

Alarms

Wrn Analog input 1 to 8

WRN

YES

Sd Analog input 1 to 8

YES

ID-DCU MARINE Binary input 1 to 14

Configurable

YES

ID-DCU MARINE Battery voltage <, >

WRN

YES

Wrn SHBIN 1 to 6

WRN

Sd SHBIN 1 to 6

Wrn DISTBIN 1 to 32

WRN

Sd DISTBIN 1 to 32

Wrn SHAIN 1 to 4

WRN

Sd SHAIN 1 to 4

Wrn CommError(1) to (10)

WRN

Sd CommError(1) to (10)

Wrn RPU Fail

WRN

Sd RPU Fail

Bw RPU FuelSol

Bw RPU StopSol

Wrn RPU Fail

WRN

Sd RPU Fail

ID-RPU A Battery voltage <, >

WRN

ID-RPU B Battery voltage <, >

WRN

Wrn DETCON

WRN

Sd DETCON

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands