ComAp InteliDrive DCU Marine Manual Download

Page: 169 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

169

Setpoint group

Date/Time

Related FW

3.0.0

Range [units]

[DISABLED, WINTER, SUMMER, WINTER-S, SUMMER-S]

Default value

DISABLED

Step

[-]

Comm object

8727

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

The setpoint is used to select mode of automatic time change.

EST (European Summer Time) started last Sunday in March. EST ends last Sunday in October.

Southern hemisphere is roughly the reverse. Time change depends on location and can vary in 8 weeks

time.

DISABLED

The automatic change to daylight saving time and back is disabled.

WINTER

The automatic change is enabled, the current season is winter and the controller is

located in the northern hemisphere.

SUMMER

The automatic change is enabled, the current season is summer and the controller is

located in the northern hemisphere.

WINTER-S

The automatic change is enabled, the current season is winter and the controller is

located in the southern hemisphere.

SUMMER-S

The automatic change is enabled, the current season is summer and the controller is

located in the southern hemisphere.

SummerTimeMod

back to List of setpoints

Setpoint group

Date/Time

Related FW

3.0.0

Range [units]

[DISABLED, ENABLED]

Default value

DISABLED

Step

[-]

Comm object

24217

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

The setpoint is used to enable Time synchronization function with InteliGen-NT and InteliSys-NT

controllers over CAN2 bus.

The synchronization is just unidirectional from InteliGen-NT or InteliSys-NT controller into InteliDrive-

DCU Marine, not vice versa.

EnTimeSync

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands