ComAp InteliDrive DCU Marine Manual Download

Page: 153 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

153

Setpoint visibility

Always

Description

Output Value of Loadsharing functional block inside ID-DCU Marine controller. It is Loadsharing: RQSP

Ramp value influenced by loadsharing variation signal (this signal can increase / decrease the RQSP Ramp

value by +/- 1,5%). The ThrottlePos value is intended to send as required speed to an engine.

Load sharing

block diagram (page 151)

See following chart describing ThrottlePos value in Running and Loadsharing state.

Note:

The regulation speed of loadsharing variation signal (max

1,5%) is given by PI loop parameters

Loadsharing: Load Gain and Load Int. The Loadsharing: ThrottlePos value is influenced by ramping

specified by Loadsharing: RQSP Ramp setpoint.

Note:

The Loadsharing state can be activated from Running state and if both following conditions are

met:

Actual Engine speed is in range specified by setpoints Loadsharing: ClutchMinSpeed and

ClutchMaxSpeed

Logical Binary input Rem Clutch is active (or I/0 front panel button is pressed)

There is loadsharing activation delay specified by setpoint Loadsharing: Clutch Del to postpone

loadsharing regulation after transient events after engine mechanical connection to gear-box.

Note:

It is essential requirement to configure engine load information (ECU value “actual load”, physical

analog input reading actuator position feedback or boost pressure etc.) into Logical Analog input Engine

Torque for loadsharing functionality.

Note:

All ID-DCU Marine controllers working in the same loadsharing group have to be interconnected

on CAN2 bus, controllers must have different controller addresses.

Note:

Loadsharing state - the Loadsharing: Back Up Speed value is taken into account instead of Engine

Values: Speed Request if the Logical Analog input Requested RPM indicates Sensor Fail (#####) and

Logical Binary input Back Up Speed is active.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands