ComAp InteliDrive DCU Marine Manual Download

Page: 50 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

4.2 Recommended wiring

4.2.1 Bus/Communication architecture

RS232

One of following possibilities is available:

PC software interface (DriveConfig, InteliMonitor).

Modbus protocol option for SCADA systems.

Analog or GSM Modem interface.

IG-IB – internet interface.

CAN1 / J1939 / KWP2000

CAN1 is data line for controller Inputs/Outputs extension. It is possible to connect following extension modules:

ECU (Engine Control Unit),

IGS-PTM (8 BI, 8BO, 4AI, 1AO),

IS-AIN8 (8AI),

IS-AIN8TC (8AI – TC only),

IS-BIN 16/8 (16BI, 8BO),

Inteli IO8/8 (8 or 16 BI, 8 or 0 BO, 2AO).

Full physical CAN interface on ID-DCU MARINE is available, no ID-COM interface needed. Maximal CAN bus

length is up to 200m

CAN2

Inter-controller CAN for multiple engines applications. ID-COM module is necessary. It is possible to connect

ID-DCU MARINE controllers and/or

IG-MU (Direct cable, analog modem or GSM modem interface) and/or

IG-IB (Internet interface) and/or

IB-NT and/or

The data rate is selectable in two levels: 250 kBd for 200 meters line and 50 kBd for 900 meters line.

CAN bus Connection rules

CAN bus line must be connected in series, from one unit to the next (no star, no cable stubs, no branches) both

ends must by the 120 Ω (internal or external) resistor terminated.

Maximal CAN2 bus length is up to 200 meters when Basic settings: CAN bus mode = 250 kBd or up to 900

meters when Basic settings: CAN bus mode = 50 kBd.

For CAN data cables details see chapter Technical data – Communication interface. CAN cable shielding

connect to ID-DCU MARINE case.

ID-DCU MARINE contains internal 120 Ω resistor over jumper setting on CAN1 bus. Use D SUB9 male

connector: CAN H = 5, CAN L = 9, COMMON = 3 and 8.

IGS-PTM unit contains internal jumper-removable 120 Ω resistor. To be sure check resistor presence by

ohmmeter. Unit with internal resistor should be connected to the end of CAN2 line.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands