ComAp InteliDrive DCU Marine Manual Download

Page: 79 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

5 Controller setup

5.1 PLC - programmable functions

Following programmable functions are available in ID-DCU MARINE-3.0.0 software.

Use DriveConfig-3.3 or higher software to configure PLC functions.

5.1.1 General specification

Each function output can be configured to:

another function input

any physical terminal (e.g. to controller’s physical Binary Output) - DriveConfig I/O sheet

Each function limit (parameter) can be configured as:

constant limit (fix): just write requested value into the field (-32768 to +32767)

setpoint limit (customer adjustable): click on field and select one from PLC setpoint list

any value (e.g. from Analog input): click on field and select one from controller or PLC values list

All PLC function analog inputs are signed type and that is why the following analog values must not be

configured to any comparator and PID analog input:

Load Sharing: ThrottlePos.

Info: ECU DiagSource, Timer val, PasswordDecode.

Statistics: NumSuccStarts, NumUnscStarts, Service time.

All function limits and analog outputs must follow input analog value format:

e.g. input value is 0,0 to 10,0 bars, then setpoint limit is e.g. 3,2.

Any time and delay limit is in 0,1s step in the range 0,1 to 3276,7 sec.

PLC consistency check indicates incorrect PLC configuration.

Binary

List contains 128 internal binary values (bits)

PLC Bout 1.1 to PLC BOUT 16.8

that

can be configured as any PLC function binary input or output.

Only used

PLC Bout x.x

can be configured to ID-DCU MARINE controller or external

modules physical terminals.

Used values are visible at controller screen.

Analog

There are available 96 internal analog values

PLC Aout 1

PLC Aout 96

that can be

configured as any PLC function input or output.

Any used

PLC Aout x

can be configured as physical analog output.Used values are

visible at controller screen.

PLC resource

Unsigned value that is automatically used for

Counter

and

Timer

functions, 16 PLC

resources are available.

Values are visible in InteliMonitor only.

PLC values

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands