ComAp InteliDrive DCU Marine Manual Download

Page: 19 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Note:

AirGate ID needed as parameter for connection creation is assigned to InternetBridge-NT (IB-NT)

module. Second parameter for connection to a particular controller is controller’s address (there can be

connected up to 8 ID-DCU Marine controllers via CAN2 bus to one IB-NT module).

2.2.2 Configuration steps

Following configuration steps are available in DriveConfig software:

Configure addresses of Extension modules when more inputs and outputs are required

Configure J1939 interface when Electronic engine is connected

Configure Binary inputs as Protection or Function

Configure Binary outputs

Configure Analog inputs as Protection or Function

Define user sensors

Configure History record

Configure password protection

Configure additional PLC logic

Modify screens for InteliVision displays

Manage ECU Fault codes

Add/Translate the language

Translator

The Translator enables to translate all or some texts to up 5 languages that could be available in controller.

Controller language can be changed from panel buttons. It is possible to operate different languages on each ID-

DCU MARINE, Remote panel and InteliMonitor.

Note:

Check all screens if some texts are not shortened.

2.2.3 Direct conection to the PC

InteliDrive can be connected directly with PC via RS232 interface. Use the standard cable RS232 cable to

connect PC with InteliDrive controller.

Note:

Make sure the grounding system on controller and PC – COM port (negative of the PC DC supply) are

identical – before the first direct connection. There must not be any voltage between these two points otherwise

the internal PTC protection activates and interrupts RS232 communication. In such case disconnect RS232

line wait a minute for PTC recovery and try again. The simple solution is to assure, that the PC supply 240/20V

is ground free (GND terminal is not connected).

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands