ComAp InteliDrive DCU Marine Manual Download

Page: 43 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

RPM

Secondary RPM

+SOL

Common power supply for galvanic separated Fuel solenoid and Stop solenoid outputs.

FUEL SOL

Fuel solenoid output, High side switch (8 Amps), BW detection in open state or above 1

amp load

STOP SOL

Stop solenoid output, High side switch (8 Amps), BW detection in open state or above 1

amp load

GND SOL

Common GND for Fuel and Stop solenoid outputs

COMM.SD

Common Shut down output, Low side switch (0,5 Amps)

COMM.WRN

Common Warning output, Low side switch (0,5 Amps)

SD1 to SD5

Shut down inputs, BW detection, Normally open

EM.STOP

Emergency stop input, Normally closed

A+, A-

Primary battery

B+, B-

Secondary battery

COM+,

COM-

Battery A, B output to ID-DCU MARINE

Note:

10 kΩ resistor must be connected in parallel to SD1 to SD5 inputs.

4.1.9 ID-SCM Speed control module

ID-SCM module is interface module for InteliDrive controller application. Module is mounted directly to ID-DCU

MARINE controller case. Module power supply: 8 to 36VDC.

Inputs

RPM1, RPM2: Two inputs for frequency (e.g. flow) measuring. Expected sensor is magnetic pickup – with

maximal frequency range up to 8 kHz. The output values SCM Freq1, SCM Freq2 calculation use setpoints

SCM unit: FreqRate1 and FreqRate2 - see below.

Closed jumper divides input frequency by 16 - recommended for higher frequency (>1000Hz) measuring.

Jumper position does not influence output value range.

Jumper

RPM input nominal frequency range

Closed

> 1000 Hz

Closed or Opened

500 - 1000 Hz

Opened

500 Hz

IMP1, IMP2: Two impulse inputs for integral (e.g. consumption) measuring. It is expected NPN – open collector

(active) impulse sensor with maximal frequency range up to 60 Hz. Minimal pulse duration is 1ms. The output

values SCM Imp1, SCM Imp2 calculation use setpoints SCM unit: TransferRate1 and TransferRate2 - see

below.

ID-SCM inputs wiring example

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands