manualshive.com logo in svg

ComAp InteliDrive DCU Marine, Manual

The ComAp InteliDrive DCU Marine is a cutting-edge control unit designed for marine applications. Access its comprehensive functionality with ease by downloading the user-friendly Reference Manual from our website, available for free. Empower your marine operations with this exceptional product from ComAp.

Share
Download
background image

InteliDrive DCU Marine - 3.0.0 Global Guide

61

4.3.8 Connection of ID-DCU MARINE analog inputs

Standard connection of resistive sensors to ID-

DCU MARINE analog inputs AI1 to AI8. The COM

terminal must be always connected to the negative

power terminal.

Different sensors connection to ID-DCU MARINE.

AI configuration jumpers must be in corresponding

position and corresponding DriveConfig

configuration according to used sensor.

Analog input common terminal COM has to be

connected to ID minus Power supply terminal.

Mixed connection of ID-DCU MARINE analog

inputs:

AI2, AI7 - current sensor

AI1, AI5 - resistive sensor

AI3, AI8 - voltage input

AI6- thermocouple (voltage)

AI4 - Not used

Mixed connection of InteliDrive analog inputs:

AI1, AI2, AI5, AI6 - resistive sensor

AI3, AI7 - binary input

AI4, AI8 - three state input

Analog input common terminal COM has to be

connected to ID minus Power supply terminal.

To ensure a proper function use shielded cables, especially for length over >3 m.

4.3.9 ID-DCU MARINE Analog inputs hardware configuration

Configure Analog inputs AI1-AI8 connection by jumpers on PCB (remove cover).

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive DCU Marine

Quectel BG96 At Command Manual preview
BG96
Brand: Quectel Pages: 23
Quectel BG96 Hardware Design preview
BG96
Brand: Quectel Pages: 79
BADODOSECURITY G200 Quick Manual preview
G200
Brand: BADODOSECURITY Pages: 8
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Danfoss VLT DriveMotor FCP 106 Installation Instructions preview
VLT DriveMotor FCP 106
Brand: Danfoss Pages: 4
Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Brand: Fagor Pages: 10
Fagor CNC 8070 Operating Manual preview
CNC 8070
Brand: Fagor Pages: 358
Fagor CNC 8070 Programming Manual preview
CNC 8070
Brand: Fagor Pages: 556
Fagor CNC 8060 Operating Manual preview
CNC 8060
Brand: Fagor Pages: 172
Fagor CNC 8060 Translation Of The Original Manual preview
CNC 8060
Brand: Fagor Pages: 180
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Brand: Fagor Pages: 112
FaderMate Master Control Unit Fittings Manual preview
Master Control Unit
Brand: FaderMate Pages: 36
Valcom V-2003A Technical Specifications preview
V-2003A
Brand: Valcom Pages: 3
Valcom V-1092 User Manual preview
V-1092
Brand: Valcom Pages: 3
Valcom V-1092 Technical Specifications preview
V-1092
Brand: Valcom Pages: 2
V2 WES-EASY Manual preview
WES-EASY
Brand: V2 Pages: 48
XtendLan KEYBPTZ4D Operating Instructions Manual preview
KEYBPTZ4D
Brand: XtendLan Pages: 12
ZBA ZZB88-441S User Manual preview
ZZB88-441S
Brand: ZBA Pages: 27

Brands by name

Popular brands

Load more brands