ComAp InteliDrive DCU Marine Manual Download

Page: 250 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

250

Related FW

3.0.0

Related applications

All

Comm object

182

Description

There are two Statistics registers Memo1 and Memo2. Those statistic values are based on Logical Analog

Input Memory1 or Memory2 value in the time of Logical Binary input Memo1 Trigger or Memo2 Trigger rising

edge. Both statistics values is possible to modify in InteliMonitor – Set Statistics command.

Memory2

back to List of LAI

Related FW

3.0.0

Related applications

All

Comm object

Description

If there is an additional terminal board between a thermocouple sensor and the IS-AIN8 (TC) module and

there is a significant temperature difference between this terminal board and the module, it is necessary to

measure the temperature at this terminal board and use this temperature for the thermocouple compensation

instead of the internal temperature of the module.

Cold Temp 1

Logical Analog input is intended for measurement of this thermocouple compensation

temperature for the IS-AIN8 (TC) module with index #1,

Cold Temp 2

corresponds to IS-AIN8 (TC) module

with index #2 etc.

Note:

Thermocouples without internal compensation "Thermo(nc)..." must be used for this case.

Cold Temp 1

back to List of LAI

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands