ComAp InteliDrive DCU Marine Manual Download

Page: 18 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Record in Alarm list

State machine indication

Oil Pressure (

MainScrAna1

) indication

Coolant Temperature (

MainScrAna2

) indication

RPM indication

2.2 Controller configuration and monitoring

InteliDrive sw pack contains separate PC software tools: DriveConfig (DC) and InteliMonitor (IMON).

DriveConfig and InteliMonitor is based on Windows 2000/XP/Vista/Win7/Win8 or higher platform.

2.2.1 AirGate connection to the PC

This connection type is used for connection to controller (s), that are connected to the Internet, however they do

not have public and static IP address. The controllers connect by InternetBridge-NT module to the AirGate

server and cyclically ask whether there is a connection request from a client or not. On the other side the clients

(only ComAp PC applications - DriveConfig, DriveMonitor InteliMonitor and WebSupervisor) connect to the

AirGate server instead of connecting directly to the controller. The server then creates a "tunnel" between the

client and the controller.

Note:

InternetBridge-NT (IB-NT) connection into Internet network can be done via Ethernet or Cellular

connection. The Ethernet connection can be realized by direct access using fixed and public IP address as well

as by private network access using dynamic non-public IP address (behind Firewall, NAT, DHCP server etc. –

situation illustrated in the picture above).

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands