ComAp InteliDrive DCU Marine Manual Download

Page: 187 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

187

Related FW

3.0.0

Related applications

All

Comm object

Description

Blocks all protections except Over-speed, Emergency Stop and protections configured as “Sd override”

(=Sprinkler).

All alarms are detected

Alarms are recorded on the controller Alarm list screen

Alarm are recorded into History

Enabled Active calls remains active

Controller front panel engine RED LED blinks or lights

Note:

The setpoint Crank Attempts is not followed if Sd Override is active, crank attempts number is

then unlimited in case of Blackout Start.

Sd Override

back to List of LBI

Related FW

3.0.0

Related applications

All

Comm object

164

Description

The Engine Values: Speed Request is decreased / increased when the binary input is closed. Speed Down

has higher priority when both Up and Down inputs are active. RPM inc/dec rate is defined by setpoint Engine

params: BI Speed ramp.

Engine speed can be set by Logical Analog Input Requested RPM or by BI Speed Up and Speed Down.

Following Speed Request initialization is valid when Analog input Requested RPM is not configured.

Speed Request (Idle) = 0,0%. Inputs are active in LOC (Local) mode.

Speed Request (Running) = 50,0% for AUX (ECU 50% = Nominal RPM).

Speed Request (Running) = 0,0% for PRP.

See Engine Values:

(page 267)

and

(page 267)

modes.

The Binary inputs SpeedUp and SpeedDown ramp

function is for the 0,6 sec constant 0,4%/s and does not

depend on Engine params: SpeedRamp setting. This

function enables fine setting of Engine speed to specific

like 1500 RPM value.

Dual rate ramp

Note:

Minimal Speed Up and Speed Down pulse duration is 110ms to be accepted by controller.

Speed Down

back to List of LBI

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands