Cognex In-Sight 1721 User Manual Download

Page: 20 / 156

Section 2: Installing the Wafer Reader

In-Sight

1700 Series Wafer Reader

2.3 Installing the In-Sight Software

A Microsoft

Windows

-based PC is required to run the In-Sight PC Host program and to

add the wafer reader to the network. The following must be installed on the PC to load
In-Sight PC Host Software:

A Microsoft Windows XP, 2000 or NT 4.0 (with Service Pack 4 or later) operating
system.

Network Interface Card (at least 100Mbps) for connecting to In-Sight wafer readers

In-Sight software (included on the CD-ROM shipped with your wafer reader).

Internet Explorer 5.01 or higher to display the

In Sight

Guide & Reference.

Perform the Following Steps to Install the In-Sight Software:

Shut down any applications on your PC.

Insert the In-Sight CD-ROM into your PC’s CD-ROM drive. If Autoplay is enabled, the
software should automatically launch the ISSetup.exe program.

Select the appropriate installation option; follow the setup dialogs as they appear on
screen.

When the installation program is complete, remove the CD from the CD-ROM drive.

If the Install Program Does Not Start Automatically:

Click the Start menu, click Run, then click Browse.

In the browse window, select the PC’s CD-ROM drive, then select the ISSetup.exe
file.

Click Open, then click OK to begin the installation.

Select the appropriate installation option; follow the setup dialogs as they appear on
screen.

When the installation program is complete, remove the CD from the CD-ROM drive.

Verify the In-Sight Software Installation:

Verify the In-Sight software installation by opening the Start menu and clicking

All

Programs

Cognex >

In-Sight

In-Sight Wafer ID (Java) 3.x.x

In-Sight PC Host.

Verify the

In Sight

Guide & Reference

help file installation by opening the Start

menu and clicking

All Programs

Cognex >

In-Sight >

In-Sight Wafer ID (Java) 3.x.x

In-Sight Help

NOTE

From the Wafer ID (Java) 3.x.x program group, select the Release Notes for current information
about In-Sight software, including new features, fixes and known issues. Registered In-Sight users

can download updated versions of In-Sight documentation at:

http://www.cognex.com/support/In-Sight.asp

Summary of Contents for In-Sight 1721





























































































































































Search results

Summary of Contents for In-Sight 1721

Reviews:

Related manuals for In-Sight 1721

Brands by name

Popular brands

Cognex In-Sight 1721, User Manual

Search results

Summary of Contents for In-Sight 1721

Reviews:

Related manuals for In-Sight 1721

Brands by name

Popular brands