Canon iR7086, Service Manual

Page: 578 / 735

Chapter 16
16-14
16.3.3 Jam Code (DADF-M1)
0011-5509
iR7086
T-16-7
0058 1st sheet pre-reversal pickup
stationary 1 S1,PI4 The 1st sheet is identified as a pre-reversal pickup stationary 1 jam (0018).
0059 1st sheet pre-reversal pickup
stationary 2 S1,PI4 The 1st sheet is identified as a pre-reversal pickup stationary 2 jam (0019).
0060 1st sheet reversal pickup
delay S2 The 1st sheet is identified as a reversal pickup delay (0020).
0061 1st sheet reversal pickup
stationary S2 The 1st sheet is identified as a reversal pickup stationary jam (0021).
0062 1st sheet pickup lead edge
skew S4,S5 The 1st sheet is identified as a pickup lead edge skew jam (0022).
0063 1st sheet pickup trail edge
skew S4,S5 The 1st sheet is identified as a pickup trail edge skew jam (0023).
0064 1st sheet pickup fault 1 S1 A pickup NG1 condition (0024) has occurred on the 1st sheet.
0065 1st sheet pickup fault 2 S3,S2 A pickup NG1 condition (0025) has occurred on the 1st sheet.
0066 1st sheet reversal pickup trail
edge skew S4,S5 A reversal pickup trail edge skew condition (0026) has occurred on the 1st sheet.
0067 1st sheet reversal pickup
NG1 PI4 The 1st sheet is identified as a reversal pickup fault 1 jam (0027).
0071 timing fault 1 - The software control mechanism has failed.
0072 timing fault 2 - In copyboard mode, an original has been read and moved to and stopped at the right side of the platen
roller; however, the preceding original has not been delayed.
0073 illegal size S3 At time of LDR stream reading, the post-registration sensor detects the original after it has been moved
a specific distance (30 mm) from the wait position.
0074 manual feed original size
error S9,S1 At time of manual feed, the reversal sensor detects an original while the manual registration roller sensor
also detects an original.
0075 image lead edge position
error S7 At time of stream reading, no change has occurred in the read position in response to a request for a
change.
0076 1st sheet image lead edge
position error S7 The 1st sheet is identified as having an image lead edge position error (0075).
0077 belt speed setting error PI1 The speed setting of the belt motor is below the minimum speed (100 mm/sec) or above the maximum
speed (700 mm/sec).
0078 belt speed switch-over error PI1 When the belt motor speed is switched over, the belt motor is not moving at a constant speed.
0079 belt status error PI1 At time of switch-over, the state is not any of the following: acceleration, constant speed rotation,
deceleration.
0080 image lead edge output
timing error S2,S3,SW301 At time of stream reading, the image lead edge signal is generated in the course of acceleration while a
move is made from the wait position to the image lead edge position.
0081 reversal speed setting error PI5 The speed setting of the reversal motor is below the minimum speed (100 mm/sec) or above the
maximum speed (700 mm/sec).
0082 reversal speed switch-over
error PI5 At time of switching over the reversal motor speed, the reversal motor is not rotating at a constant speed.
0083 reversal status error PI5 At time of switch-over, the state of the reversal motor is not any of the following: acceleration, constant
speed, deceleration.
0084 last original error PI1 A belt motor error occurs while the last original is being discharged by the platen roller or being moved.
0085 error PI1,PI2,PI11 A motor error other than an IPC communication or pickup error has occurred. (less than 3 times)
0090 ADF open PI10 The ADF is identified as being open.
0091 user DF open PI10 The ADF is identified as being open while the machine is operating.
0092 cover open PI3,PI6 The cover is identified as being open.
0093 user cover open PI3,PI6 The cover (front or rear) is identified as being open while the machine is operating.
0094 initial stationary PI4,PI12,PI13,S
1,S2,S3,S4,S5,S
9 At the start of operation, a sensor inside the paper path detects an original.
0095 cycle fault S6 The pickup signal has been received for a specific period of time (2 sec) in the absence of a detected
original.
0096 residual original S1 The reversal sensor detects an original while the belt motor is moved for a specific distance before the
start of a left pickup job.
0097 manual feeder residual
original S1,S9 At time of manual feed pickup, the reversal sensor detects an original while the manual feeder registration
roller sensor also detects an original.
0098 power-down - A drop occurs in the voltage supplied by the host machine while the machine is operating.
Code Sensor Notation Description
0001 post-separation sensor PI7 The post-separation sensor does not detect paper when paper has been moved 452 mm
after the start of separation.
Code Sensor type Sensor No. Description