Canon iR7086, Service Manual

Page: 577 / 735

Chapter 16
16-13
0011 pre-reversal delay 2 S1,S3 At time of pre-reversal, the reversal sensor does not detect the original after it has been moved a specific
distance (100 mm) after the post-registration roller sensor has gone on.
0012 pre-reversal delay 3 PI4 At time of pre-reversal, the reversal sensor does not detect the original when it has been moved over a
specific distance (100 mm) after the reversal motor has stopped.
0013 pre-reversal stationary 1 S1,S4 At time of reversal, the separation sensor has detected the original when it has been moved over a specific
distance (169 mm) after the reversal sensor has gone on.
0014 pre-reversal stationary 2 S2,S4 At time of pre-reversal, the pre-registration sensor has detected the original when it has been moved over
a specific distance (120 mm) after its trail edge has moved past the separation pull-off roller.
0015 pre-reversal stationary 3 S2,S3 At time of pre-reversal, the post-registration roller sensor detects the original after it has been moved a
specific distance (50 mm) following the passage of the trail edge of the original for the pre-registration
roller sensor.
0016 pre-reversal stationary 4 S1,S3 At time of pre-reversal, the reversal sensor detects the original after it has been moved a specific distance
(100 mm) following the passage of the trail edge of the original from the pre-registration roller sensor.
0017 pre-reversal pickup delay S1 At time of pre-reversal pickup, the reversal sensor does not detect the original after it has been moved a
specific distance (100 mm) following the start of the reversal sensor.
0018 pre-reversal pickup
stationary 1 S1,PI4 At time of pre-reveal, the pre-reversal sensor has detected the original when it has been moved over a
specific distance after the reversal sensor has detected its lead edge.
0019 pre-reversal pickup
stationary 2 S1,PI4 At time of pre-reversal pickup, the reversal sensor detects the original after it has been moved a specific
distance following the detection of its trail edge by the pre-reversal sensor.
0020 reversal pickup delay S2 At time of reversal, the pre-registration roller sensor does not detect the original after it has been moved
a specific distance (197 mm) following the end of arching operation.
0021 reversal pickup stationary S2 At time of reversal, the pre-registration roller sensor detects the original after it has been moved a specific
distance (original length X 1.5 mm) following the start of the pre-registration roller sensor.
0022 pickup lead edge skew S4,S5 At time of separation, there is a discrepancy of an equivalent of 10 mm in the timing of detecting the lead
edge between the separation sensor and the skew sensor.
0023 pickup trail edge skew S4,S5 At time of pickup, there is a discrepancy of an equivalent of 10 mm in the timing of detecting the trail
edge between the separation sensor and the skew sensor.
0024 pickup fault 1 S1 At time of pickup, the reversal sensor detects an original before it moves past the pre-registration roller
sensor.
0025 pickup fault 2 S3,S2 At time of pickup, the post-registration sensor detects an original before the start of the reversal motor.
At time of pickup, the pre-registration roller sensor does not detect the original after it has been moved a
specific distance.
At time of pre-reversal, the pre-registration roller sensor detects an original before the start of the reversal
motor.
At time of reversal, the pre-registration roller sensor does not detect the original while its trail edge is
moving past the reversal sensor.
0026 reversal pickup trail edge
skew S4,S5 At time of pre-reversal, there is a discrepancy of an equivalent of 10 mm in the timing of detecting the
trail edge between the separation sensor and the skew sensor.
0027 reversal pickup fault 1 PI4 At time of reversal, the pre-reversal sensor detects the original during a wait for the activation of the pre-
registration roller sensor.
0030 manual feed registration
delay S9 At time of arching operation in manual feed mode, the manual feeder registration roller sensor does not
detect an original within a specific period of time (1 sec) from the start of the delivery motor.
0031 manual feed registration
delay S1 At time of pickup from the manual feeder, the reversal sensor does not detect the original after it has been
moved a specific distance (638 mm) following the start of the belt motor.
0032 manual feeder reversal
stationary S1 At time of pickup from the manual feeder (platen roller), the reversal sensor does not detect the original
after it has been moved a specific distance (50 mm) following the start of the belt motor.
0033 manual feed delivery delay PI13 At time of manual feed delivery, the delivery sensor does not detect the original after it has been moved
a specific distance (621 mm - original length).
0034 manual feed delivery
stationary PI13 At time of manual feed delivery, the delivery sensor detects the original after it has been moved a specific
distance (original length x 1.5) following the activation of the delivery sensor.
0043 1st sheet pickup stationary 1 S3 The 1st sheet is identified as a pickup delivery 1 jam (0003).
0044 1st sheet pickup stationary 2 S2 The 1st sheet is identified as a pickup stationary 2 jam (0004).
0045 1st sheet reversal delay S1 The 1st sheet is identified as a reversal delay jam (0005).
0046 1st sheet reversal stationary S1 The 1st sheet is identified as a reversal stationary jam (0006).
0047 1st sheet delivery delay PI13 The 1st sheet is identified as a delivery delay jam (0007).
0048 1st sheet delivery stationary
1 PI13,S9 The 1st sheet is identified as a delivery delay jam (0008).
0049 1st sheet delivery stationary
2 PI13,S9 The 1st sheet is identified as a delivery stationary 2 jam (0009).
0050 1st sheet pre-reversal delay 1 S3 The 1st sheet is identified as a pre-reversal delay 1 jam (0010).
0051 1st sheet pre-reversal delay 2 S1,S3 The 1st sheet is identified as a pre-reversal delay 2 jam (0011).
0052 1st sheet pre-reversal delay 3 PI4 The 1st sheet is identified as a pre-reversal delay 3 jam (0012).
0053 1st sheet pre-reversal
stationary 1 S1,S4 The 1st sheet is identified as a pre-reversal stationary 1 jam (0013).
0054 1st sheet pre-reversal
stationary 2 S2,S4 The 1st sheet is identified as a pre-reversal stationary 2 jam (0014).
0055 1st sheet pre-reversal
stationary 3 S2,S3 The 1st sheet is identified as a pre-reversal stationary 3 jam (0015).
0056 1st sheet pre-reversal
stationary 4 S1,S3 The 1st sheet is identified as a pre-reversal stationary 4 jam (0016).
0057 1st sheet pre-reversal pickup
delay S1 The 1st sheet is identified as a pre-reversal pickup delay jam (0017).
Code Sensor type Sensor No. Description