Canon iR7086, Service Manual

Page: 576 / 735

Chapter 16
16-12
16.3 Jam Code
16.3.1 Jam Code (printer)
0011-5508
iR7105 / iR7095 / iR7086
T-16-5
16.3.2 Jam Code (DADF-Q1)
0011-5512
iR7105 / iR7095
T-16-6
*12
10
12
14
22
23
24
A system error or a packet error
has been detected.
- Start up in safe mode, and perform full formatting using the SST and reinstall the system software; then,
turn off and back on the power.
- Replace the HDD, and reinstall the system software.
Code Jam type Sensor type Sensor No.
01xx delay jam See the table
02xx stationary jam
0Axx power-on residual jam
0Bxx door open jam
0C00 double-feeding double-feeding sensor (reception) PS65
Code Sensor type Sensor No. Code Sensor type Sensor No.
xx01 right deck pickup sensor PS20 xx0F duplexing reversal sensor PS12
xx02 left deck pickup sensor PS25 xx10 duplexing outlet sensor PS61
xx03 cassette 3 pickup sensor PS37 xx11 pre-confluence sensor PS14
xx04 cassette 4 pickup sensor PS42 xx12 post-confluence sensor PS15
xx05 vertical path 1 paper sensor PS47 xx13 left deck feed sensor PS26
xx06 vertical path 2 paper sensor PS49 xx14 right deck feed sensor PS27
xx07 vertical path 3 paper sensor PS41 xx15 side paper deck feed sensor PS106
xx08 vertical path 4 paper sensor PS46 xx16 multifeeder curl-removal sensor PS68
xx09 registration roller sensor PS5 xx17 side paper deck pickup sensor PS101
xx0A fixing claw jam sensor PS65 xx18 image write start sensor PS60
xx0B inside delivery sensor PS9 xx19 manual feeder feed sensor PS35
xx0C outside delivery sensor PS10 xx1A fixing inlet sensor PS63
xx0D fixing feed unit outlet sensor PS11
Code Sensor type Sensor No. Description
0001 separation delay S4 At time of separation, the separation sensor does not detect the original after it has been moved a specific
distance (221 mm) following the start of the separation motor.
0002 pickup delay S4,S2 At time of separation, the pre-registration roller sensor does not detect the original after it has been moved
a specific distance (93 mm) following the detection of its lead edge by the separation sensor.
0003 pickup stationary 1 S3 At time of pickup, the post-registration sensor does not detect the original after it has been moved a
specific distance (40 mm) following the start of the reversal motor.
0004 pickup stationary 2 S2 At time of pickup, the pre-registration roller sensor detects the original after it has been moved a specific
distance (330 mm if small; 660 mm if large) following the start of the reversal motor.
0005 reversal delay S1 At time of reversal, the reversal sensor does not detect the original after it has been moved a specific
distance (104 mm) from the platen roller.
0006 reversal stationary S1 At time of reversal, the reversal sensor detects the original after it has been moved a specific distance
(original length x 1.5 mm) following arching operation.
0007 delivery delay PI13 At time of delivery, the delivery sensor does not detect the original after it has been moved a specific
distance (631 mm - original length) following the start of the belt motor.
0008 delivery stationary 1 PI13,S9 At time of delivery, the manual feeder registration roller sensor detects the original after it has been
moved a specific distance (original 100 mm) following the activation of the delivery sensor.
0009 delivery stationary 2 PI13,S9 At time of delivery, the delivery sensor detects the original after it has been moved a specific distance
(original 100 mm) following the deactivation of the manual feeder registration roller sensor.
0010 pre-reversal delay 1 S3 At time of pre-reversal, the post-registration roller sensor does not detect the original after it has been
moved a specific distance (50 mm) following the activation of the reversal motor.
YY Description Action