Canon iR7086, Service Manual

Page: 572 / 735

Chapter 16
16-8
E711 An error has occurred in the communication between the pickup/delivery accessory and the printer unit.
0001 Indicates the recognition failure of the delivery options on ARCNET network. Turn off and then back on the power. (Turn off the machine
and its delivery accessories;
then, turn back on all accessories and then the machine.)
Connect the communication
cables and terminals between the machine and the delivery
accessories once again.
Replace the accessories controller PCB. Replace the
transceiver PCB.
0002 Indicates the optional communication control failure.
0003 Indicates no response from the delivery options.
E712 An error exists in the communication between the ADF and the reader unit.
0001 As much as 5 sec or more has passed without recovery after communication
stopped
between the reader controller and the ADF controller. Disconnect and then connect the connectors between the
reader unit and the ADF. Replace
the reader controller PCB. Replace the ADF controller PCB.
E717 An error exists in the communication with the NE controller.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 The NE controller that has been connected before power-off is not recognized
at power-on. Disconnect and then connect the main controller PCB. Install
the NE controller. Replace
the NE controller.
0002 An error that cannot be reset (e.g., cable break) has been detected in the
communication.
E719 An error has occurred in the communication with the coin vendor/card reader.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 The coin vendor that was connected before power-off is not recognized at
power-on. Disconnect and then connect the connector of the main
controller PCB. Install the coin
vendor. Replace the coin vendor.
0002 In the communication with the coin vendor, an error that cannot be reset has
occurred (e.g.,
cable break).
0003 In the communication with the coin vendor, a communication error has
occurred during
acquisition of unit price information.
0011 The card reader that was connected before power-off is not recognized at
power-on. Disconnect and then connect the connector of the main
controller PCB. Install the card
reader. Replace the card reader.
0012 In the communication with the card reader, an error that cannot be reset has
occurred (e.g.,
cable break).
E730 A PDL-related error has occurred.
1001 An initialization error has occurred at the start of a job. Reset the PDL mechanism. Turn off and then on the power.
100A An error has occurred in the communication with an external controller.
9004 A fault has been detected in the cable connection with an external controller. Turn off and then on the power. Replace the external
controller relay PCB. Replace the
external controller.
9005 A fault has been detected in the cable connection with an external controller.
A006 The PDL mechanism does not respond. Reset the PDL mechanism. Turn off and then on the power.
Reinstall the system software.
Replace the main controller.
A007 At start-up, the version of the machine control software and that of the PDL
control
software do not match. Reset the PDL mechanism. Turn off and then on the power.
Execute full formatting of the
HDD, and reinstall the system software.
B013 The font data is corrupted at start-up. Turn off and then on the power. Reinstall the system software.
Execute full formatting of
the HDD, and reinstall the system software.
E732 An error has occurred in the communication between the reader unit and the main
controller.
0001 An error has occurred in the communication between the reader unit and the
main
controller. Disconnect and connect the connectors of the read
communication cable. Check the
power supply of the reader unit (to see if initialization occurs
at power-on). Replace the
reader controller PCB. Reap the reader I/F PCB. Replace the
main controller PCB.
0010 A fault has been detected in the reader sync signal detection mechanism.
E733 An error has occurred in the communication between the reader unit and the main
controller.
0000 An error has occurred in the communication between the reader unit and the
main
controller. Disconnect and then connect the connector. Check the power
supply of the DC controller (to
see if initialization occurs at time of start-up). Replace the DC
controller PCB. Replace the
main controller PCB.
0001 An attempt to communicate with the DC controller fails.
0010 A fault has occurred in the printer engine sync signal detection mechanism.
E740 An error exists in the LAN controller.
0002 An illegal MAC address has been detected at start-up. Replace the main controller PCB.
E743 A fault exists in the communication between the main controller and the reader controller.
0000 The reader controller has detected an error in the communication between the
main
controller and the reader controller. Disconnect and then connect the connectors of the reader
communications cable. Replace
the reader controller PCB. Replace the main controller PCB.
E744 An error exists in the language file/boot ROM.
Code Description Remedial action
*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086).
**: model equipped with DADF-M1 (outside Japan: iR7086).