Canon imageRunner 2022, Service Manual

Page: 342 / 418

Chapter 15
15-20
15.5.8 <016: time length to first response at time of fax/tel switchover>
0017-6108
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Allows setting of the time from seizing the line till pseudo RBT is sent, when the Fax/ Tel switching function is operating.
15.5.9 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:
pseudo RBT signal pattern OFF time length (long)>
0017-6109
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set the pattern of the pseudo RBT signal transmitted at time of a fax/tel switchover.
15.5.10 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)>
0017-6110
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set the pseudo CI signal pattern transmitted at time of a fax/tel switchover.
15.5.11 <023: CNG detention level for fax/tel switchover>
0017-6111
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set the CNG detention level for a fax/tel switchover.
15.5.12 <024: pseudo RBT transmission level at time of fax/tel switchover>
0017-6112
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set the pseudo transmission level for a fax/tel switchover.
15.5.13 <025: Answering machine connection function signal detection time>
0017-6113
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Sets the signal detection time for the answering machine connection function operation. When the answering machine connection function is operating, if the func-
tion does not operate normally because the fax does not detect CNG signal sent from the line, raise this parameter to increase the signal detection time.
15.5.14 <027: V.21 low-speed flag preamble identification length>
0017-6114
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to detect the time of detection after which command analysis is started after detecting V.21 low-speed command preambles continuously for a specific period
of time.
15.5.15 <055: Acquisition period of environmental log data>
0017-8531
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to change the acquisition period of environmental log data.
15.5.16 <056 - 061: Count type select >
0017-6115
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to confirm the count type indicated on the Counter Check screen, which appears in response to a press on the Counter key.
When '0' is selected, count type will not be indicated.
No.56: Use it to indicate the type of software counter 1 of the control panel. The type of soft counter 1 cannot be changed.
No.57: Use it to change the type of soft counter 2* of the control panel to suit the needs of the user.
No.58: Use it to change the type of soft counter 3* of the control panel to suit the needs of the user.
No.59: Use it to change the type of soft counter 4* of the control panel to suit the needs of the user.
No.60: Use it to change the type of soft counter 5* of the control panel to suit the needs of the user.
No.61: Use it to change the type of soft counter 6* of the control panel to suit the needs of the user.
*:The default type settings of soft counter is different from models.
<Soft Counter Specifications>
The soft counters are classified a follows in terms of input numbers:
100s: total
200s: copy
300s: print
400s: copy + print
500s: scan
700s: received file print
800s: report pint
900s: transmitted scan
Guide to the Table
- 1:Count sheets of all sizes by one.
- 2:Count sheets of the large size by two.
- C:full color
- Bk:black mono
- L:large size (larger than A4/LTR)
- S:small size (A4/LTR or smaller)
MEMO:
To make a change so that B4 papers (for print) will be counted as large-size, use service mode: make the following selections, and change bit 0 to '1': #SSSW>SW33.
To make a change so that B4 papers (for scan) will be counted as large-size, use service mode: make the following selections, and change bit 2 to '1': #SSSW>SW33.