manualshive.com logo in svg

Cadillac ESCALADE EXT 2002, Manual

The Cadillac ESCALADE EXT 2002 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and maintaining your vehicle. Download the manual now from manualshive.com to ensure the best performance and longevity of your Cadillac ESCALADE EXT 2002.

Share
Download
background image

4-43

CAUTION:

Snow can trap exhaust gases under your vehicle.
This can cause deadly CO (carbon monoxide) gas
to get inside. CO could overcome you and kill
you. You can’t see it or smell it, so you might not
know it is in your vehicle. Clear away snow from
around the base of your vehicle, especially any
that is blocking your exhaust pipe. And check
around again from time to time to be sure snow
doesn’t collect there.

Open a window just a little on the side of the
vehicle that’s away from the wind. This will help
keep CO out.

Run your engine only as long as you must. This saves
fuel. When you run the engine, make it go a little faster
than just idle. That is, push the accelerator slightly. 
This uses less fuel for the heat that you get and it 
keeps the battery charged. You will need a well

-

charged

battery to restart the vehicle, and possibly for signaling
later on with your headlamps. Let the heater run for 
a while.

Then, shut the engine off and close the window almost
all the way to preserve the heat. Start the engine again
and repeat this only when you feel really uncomfortable
from the cold. But do it as little as possible. Preserve the
fuel as long as you can. To help keep warm, you can get
out of the vehicle and do some fairly vigorous exercises
every half hour or so until help comes.

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ESCALADE EXT 2002

UnderCover 2110 Installation Manual preview
2110
Brand: UnderCover Pages: 16
Lancia Delta Owner'S Handbook Manual preview
Delta
Brand: Lancia Pages: 276
T-Tech TT100 User Manual preview
TT100
Brand: T-Tech Pages: 38
J-Top COMPACT Instructions preview
COMPACT
Brand: J-Top Pages: 2
Raven CR7 Calibration Manual preview
CR7
Brand: Raven Pages: 24
Weather Guard 237 Assembly And Installation Instructions preview
237
Brand: Weather Guard Pages: 4
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
IAG IAG-ENG-5003BK Instructions preview
IAG-ENG-5003BK
Brand: IAG Pages: 3
Alpine eX-10 Owner'S Manual preview
eX-10
Brand: Alpine Pages: 69
Allen Sports S302 Instructions preview
S302
Brand: Allen Sports Pages: 2
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Brand: FORM FIT Pages: 2
Chevrolet 2013 Spark Specifications preview
2013 Spark
Brand: Chevrolet Pages: 2
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Brand: iRacing Pages: 25
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Brand: Ecco Pages: 12
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Brand: Gator Pages: 8
benbat BM721 Instructions For Use Manual preview
BM721
Brand: benbat Pages: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Brand: SPL Pages: 5
FALCON RIDGE HU-4421-XL-SDK01 Instructions For Installation And Care preview
HU-4421-XL-SDK01
Brand: FALCON RIDGE Pages: 5

Brands by name

Popular brands

Load more brands