manualshive.com logo in svg

Cadillac ESCALADE EXT 2002, Manual

The Cadillac ESCALADE EXT 2002 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and maintaining your vehicle. Download the manual now from manualshive.com to ensure the best performance and longevity of your Cadillac ESCALADE EXT 2002.

Share
Download
background image

3-25

After you clean the player, press and hold EJECT for
five seconds to reset the CLN indicator. The radio will
display 

---

 to show the indicator was reset.

Cassettes are subject to wear and the sound quality 
may degrade over time. Always make sure the cassette
tape is in good condition before you have your tape
player serviced.

Care of Your Compact Discs

Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution and
clean it, wiping from the center to the edge.

Be sure never to touch the side without writing when
handling discs. Pick up discs by grasping the outer 
edges or the edge of the hole and the outer edge.

Care of Your Compact Disc Player

The use of CD lens cleaner discs is not advised, due to
the risk of contaminating the lens of the CD optics with
lubricants internal to the CD mechanism.

Fixed Mast Antenna

The fixed mast antenna can withstand most car washes
without being damaged. If the mast should ever become
slightly bent, you can straighten it out by hand. If the
mast is badly bent, as it might be by vandals, you should
replace it.

Check every once in a while to be sure the mast is still
tightened to the cowl. If tightening is required, tighten
by hand, then with a wrench one quarter turn.

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ESCALADE EXT 2002

Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Brand: Kolpin Pages: 25
Whispbar K934W Fitting Instructions Manual preview
K934W
Brand: Whispbar Pages: 15
muth signal mirror Instalation Instructions preview
signal mirror
Brand: muth Pages: 10
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Brand: Wagan Pages: 20
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Brand: EZTRUNK Pages: 3
Volvo B13R Driver'S Handbook Manual preview
B13R
Brand: Volvo Pages: 24
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Brand: Ranger design Pages: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Brand: AUTOTECH Pages: 1
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
Cadillac 2001 Eldorado Owner'S Manual preview
2001 Eldorado
Brand: Cadillac Pages: 335
Westfalia 859528 Original Instructions Manual preview
859528
Brand: Westfalia Pages: 10
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Brand: Brodit Pages: 2
Safe Fleet PRIME DESIGN UXV 211 Quick Start Manual preview
PRIME DESIGN UXV 211
Brand: Safe Fleet Pages: 8
3SIXT 3S-1802 Operating Instructions preview
3S-1802
Brand: 3SIXT Pages: 4
SMART cabriolet Maintenance Booklet preview
cabriolet
Brand: SMART Pages: 26
Westin 46-24025 Installation Instructions Manual preview
46-24025
Brand: Westin Pages: 9
RADICAL R-C10-DAB Installation Manual preview
R-C10-DAB
Brand: RADICAL Pages: 4

Brands by name

Popular brands

Load more brands