manualshive.com logo in svg

Cadillac ESCALADE EXT 2002, Manual

The Cadillac ESCALADE EXT 2002 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and maintaining your vehicle. Download the manual now from manualshive.com to ensure the best performance and longevity of your Cadillac ESCALADE EXT 2002.

Share
Download
background image

4-51

Weight of the Trailer

How heavy can a trailer safely be?

It depends on how you plan to use your rig. For example,
speed, altitude, road grades, outside temperature and 
how much your vehicle is used to pull a trailer are all
important. And, it can also depend on any special
equipment that you have on your vehicle.

Use one of the following charts to determine how much
your vehicle can weigh, based upon your vehicle model
and options.

Maximum trailer weight is calculated assuming only the
driver is in the tow vehicle and it has all the required
trailering equipment. The weight of additional optional
equipment, passengers and cargo in the tow vehicle
must be subtracted from the maximum trailer weight.

NOTICE:

Your vehicle was not designed to be used with a
fifth

-

wheel hitch device. Using such a device

could result in damage to the vehicle.
This damage would not be covered by your
vehicle’s warranty.

Vehicle

Axle

Ratio

Max.

Trailer Wt.

**GCWR

AWD 6.0 L

3.73

7, 900 lbs.
(3 583 kg)

14, 000 lbs.

(6 350 kg)

* Tongue weight should be 10 percent to 15 percent of
trailer weight up to 1,000 lbs. (453 kg) maximum.

**The Gross Combination Weight Rating (GCWR) 
in the total allowable weight of the completely loaded
vehicle and trailer including any passengers, cargo,
equipment and conversions. The GCWR for your
vehicle should not be exceeded.

You can ask your dealer for our trailering information or
advice, or you can write us at the address listed in your
Warranty and Owner Assistance Information Booklet.

In Canada, write to:

General Motors of Canada Limited
Customer Communication Centre, 163

-

005

1908 Colonel Sam Drive
Oshawa, Ontario L1H 8P7

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ESCALADE EXT 2002

cam 2850 Mounting Instructions preview
2850
Brand: cam Pages: 2
Dapper Lighting 575 Install Manual preview
575
Brand: Dapper Lighting Pages: 2
Tamiya KO PROPO RTF 2002 ESC Manual preview
KO PROPO RTF 2002 ESC
Brand: Tamiya Pages: 2
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Brand: Xpresskit Pages: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Brand: RAM Pages: 92
BMW E46/2 Coupe Manual preview
E46/2 Coupe
Brand: BMW Pages: 55
Whispbar K496W Fitting Instructions Manual preview
K496W
Brand: Whispbar Pages: 15
Volvo 1996 960 Quick Tips preview
1996 960
Brand: Volvo Pages: 10
Fiat Fiat Bravo LPG Owner'S Manual preview
Fiat Bravo LPG
Brand: Fiat Pages: 24
Valeo AS1A Owner'S Manual preview
AS1A
Brand: Valeo Pages: 28
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Brand: SCC Pages: 4
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Brand: STARLANE Pages: 24
Yakima Prorack K436 Fitting Instructions Manual preview
Prorack K436
Brand: Yakima Pages: 13
BMW 323Ci Manual preview
323Ci
Brand: BMW Pages: 189
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Brand: Safe Fleet Pages: 12
N.R. AUTOSEATS Top User Manual preview
Top
Brand: N.R. AUTOSEATS Pages: 8
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Brand: Voxx Electronics Pages: 15
Subaru SPN0001105 User Manual preview
SPN0001105
Brand: Subaru Pages: 44

Brands by name

Popular brands

Load more brands