Cadillac ESCALADE EXT 2002 Manual Download Page 309

Page: 309 / 427

5-34

4. Insert the hoist end (F)

through the hole (G)
in the rear bumper and
into the hoist shaft.

5. Raise the tire partway upward. Make sure the

retainer is seated in the wheel opening.

6. Raise the tire fully against the underside of the

vehicle. Continue turning the wheel wrench until
the tire is secure and the cable is tight. The spare
tire hoist cannot be overtightened.

7. Make sure the tire is stored securely. Push, pull, and

then try to rotate or turn the tire. If the tire moves,
use the wheel wrench to tighten the cable.

To store the tools, follow these procedures:

1. Return the tools to the tool bag and place it

back in the Top

Box storage area.

2. Assemble the wheel blocks and bottle jack

together with the wing nut.

3. Replace the jack cover and tighten the

jack

cover wingnuts.

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Search results

Summary of Contents for ESCALADE EXT 2002

Reviews:

Related manuals for ESCALADE EXT 2002

Brands by name

Popular brands

Cadillac ESCALADE EXT 2002, Manual

Search results

Summary of Contents for ESCALADE EXT 2002

Reviews:

Related manuals for ESCALADE EXT 2002

Brands by name

Popular brands