Cadillac ESCALADE EXT 2002 Manual Download Page 298

Page: 298 / 427

5-23

Follow these instructions to lower the spare tire:

1. Your vehicle is equipped with a hoist lock (J).

To unlock it, open the spare tire lock cover on the
bumper and use the ignition key to remove the lock.

2. Assemble the wheel wrench (H) and the two jack

handle extensions (I) as shown.

3. Insert the hoist end

(open end) (F) of the
extension through
the hole (G) in the
rear bumper.

Be sure the hoist end of the extension connects into the
hoist shaft (E). The ribbed square end of the extension is
used to lower the spare tire.

4. Turn the wheel wrench (H) counterclockwise to

lower the spare tire to the ground. Continue to turn
the wheel wrench until the spare tire can be pulled
out from under the vehicle.

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Search results

Summary of Contents for ESCALADE EXT 2002

Reviews:

Related manuals for ESCALADE EXT 2002

Brands by name

Popular brands

Cadillac ESCALADE EXT 2002, Manual

Search results

Summary of Contents for ESCALADE EXT 2002

Reviews:

Related manuals for ESCALADE EXT 2002

Brands by name

Popular brands