Cadillac ESCALADE EXT 2002 Manual Download Page 340 | Manualshive

Page: 340 / 427

background image

6-28

Checking Coolant

The coolant surge tank
is located in the engine
compartment on the
passenger’s side of
the vehicle.

See “Engine Compartment Overview” in the Index for
more information on location.

CAUTION:

Turning the surge tank pressure cap when the
engine and radiator are hot can allow steam and
scalding liquids to blow out and burn you badly.
Never turn the surge tank pressure cap

--

even a

little

--

when the engine and radiator are hot.

The vehicle must be on a level surface. When your
engine is cold, the coolant level should be at the FULL
COLD mark.

If the LOW COOLANT
message comes on and stays
on, it means you’re low on
engine coolant.

See “Low Coolant” in the Index.

«
...
338
339
340
341
342
...
»

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ESCALADE EXT 2002

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: Thule Pages: 8

Brand: CITROËN Pages: 301

Brand: Rola Pages: 3

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Brand: Toyota Pages: 52

VIEWLINE 52 MM - MOUNTING 11-09

Brand: VDO Pages: 4

Brand: Xblitz Pages: 30

Brand: Quadratec Pages: 12

Brand: RAM Pages: 496

Brand: Cadillac Pages: 409

Brand: Fortin Pages: 9

Brand: ULTIMATE SPEED Pages: 34

Brand: Axxess Pages: 8

Brand: SSV Works Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands