Cadillac ESCALADE EXT 2002 Manual Download Page 330 | Manualshive

Page: 330 / 427

background image

6-18

1. To remove the engine air cleaner/filter, loosen the

screws on the cover.

2. Lift the cover upward and remove the engine air

cleaner/filter out of the air cleaner housing. Care
should be taken to dislodge as little dirt as possible.

3. Clean the filter sealing surface and the housing.

4. Install the new engine air cleaner/filter.

5. Install the cover and tighten the screws.

Refer to the Maintenance Schedule to determine when to
replace the engine air cleaner/filter. See “Owner Checks
and Services” in the Index.

CAUTION:

Operating the engine with the air cleaner/filter
off can cause you or others to be burned. The air
cleaner not only cleans the air, it stops flame if
the engine backfires. If it isn’t there, and the
engine backfires, you could be burned. Don’t
drive with it off, and be careful working on the
engine with the air cleaner/filter off.

NOTICE:

If the air cleaner/filter is off, a backfire can cause
a damaging engine fire. And, dirt can easily get
into your engine, which will damage it. Always
have the air cleaner/filter in place when you’re
driving.

«
...
328
329
330
331
332
...
»

Summary of Contents for ESCALADE EXT 2002












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ESCALADE EXT 2002

Brand: Daihatsu Pages: 43

Brand: Harken Hoister Pages: 12

Brand: Yamaha Pages: 2

Brand: LAMBORGHINI Pages: 48

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: GMC Pages: 20

Brand: iDataLink Pages: 99

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: Xhorse Pages: 48

Brand: Axxess Pages: 8

Brand: Dodge Pages: 276

Brand: Horn Tools Pages: 12

Brand: Metra Electronics Pages: 20

3 Facelift 2006

Brand: Mazda Pages: 94

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Subaru Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands