Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 176 / 364

background image

KNX control elements and application parameters

"Display" control element

Product manual 2CKA001473B5342

│

176

10.13.9 Type of display element — Linear measurement display — Measurement display with

colour display

Options:

Deactivated

Activated

The parameter is used to specify whether a colour display follows. For this the communication
objects "Switch alarm", "Switch warning", and "Switch information" are enabled.

10.13.10 Type of display element — Linear measurement display — Display value in control

element

Options:

Deactivated

Activated

The parameter is used to specify whether the value of the selected element is displayed in the
display element.

–

Deactivated

: No display. No additional parameters available.

–

Activated

: The following supplementary parameters are displayed:

Unit

:

Options:

<Text>

The parameter is used to enter the unit or the unit sign with which the measured value is

displayed in the display element.

The length of the text is limited to 60 characters.

Decimal places

:

Options:

Setting option from 0 - 2

The parameter is used to specify the number of decimal places of the displayed measured
value.

The number is limited to 2 places.

Thousands separator

:

Options:

Deactivated

Activated

The parameter is used to specify whether a thousands separator is displayed in the
measured value.

«
...
174
175
176
177
178
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: Q CELLS Pages: 12

intelligent Touch Manager

Brand: Daikin Pages: 44

Brand: WINAICO Pages: 15

Brand: DIGI-STAR Pages: 13

Brand: Winmate Pages: 28

Brand: AEG Pages: 11

CyberMed M10 Series

Brand: Cybernet Pages: 29

Brand: COMECO Pages: 12

Brand: Autobase Pages: 30

Brand: Canadian Solar Pages: 28

Brand: CORAB Pages: 6

Brand: IEI Technology Pages: 48

Brand: IEI Technology Pages: 100

PoleTops 5001 Series

Brand: UNIRAC Pages: 4

Brand: Sferasol Energy Pages: 20

Brand: AERMEC Pages: 15

Brand: Brown & Watson Pages: 20

Brand: i3-TECHNOLOGIES Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands