Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 207 / 364

background image

KNX control elements and application parameters

Application "Fault and alarm messages" - Settings of the individual messages

Product manual 2CKA001473B5342

│

207

Designation of message. The length of the name is limited to 60 characters.

10.19.2 Type of message

Options:

Alarm

Notice

Error

The parameter is used to specify the type of message that is displayed.

10.19.3 Type of alarm

Options:

1 bit

14 bytes

The parameter is used to specify whether the alarm is displayed and sent with or without text.

–

1 bit

: No text is displayed and sent when acknowledging the alarm. The following

supplementary parameters are available:

Text for alarm message

:

Options:

<Text>

The parameter is used to specify the text that is displayed when this message appears. The
length of the text is limited to 60 characters.

Sending 0 at acknowledgement

:

Options:

Deactivated

Activated

The parameter is used to specify whether "0" is sent at acknowledgement.

Acoustic alarm signal

:

Options:

Deactivated

Activated

The parameter is used to specify whether the signal tone specified under the global settings
is played see chapter 10.18 “Application "Fault and alarm messages" - Global settings“ on
page 205.
–

Deactivated

: No acoustic alarm signal. No additional parameters available.

–

Activated

: The signal tone is played at an alarm signal. The following supplementary

parameter is available:

Duration of audio signal [min.]

:

Options:

Setting option from 1 - 60

The parameter is used to specify how long the specified signal tone is to be played (in
minutes).

«
...
205
206
207
208
209
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: YASKAWA Pages: 56

Brand: EBN Technology Pages: 16

Brand: Colormetrics Pages: 91

Brand: Toshiba Pages: 22

Brand: Toshiba Pages: 182

Brand: Xinje Pages: 81

Brand: Abexo Pages: 15

TMG-310-DC00-01

Brand: Seedsware Pages: 41

Brand: UNIRAC Pages: 4

Brand: FANTEM Pages: 8

3000 Series T31P

Brand: OHAUS Pages: 44

Brand: Samlexpower Pages: 8

Cutler-Hammer PanelMate

Brand: Eaton Pages: 26

Brand: Eaton Pages: 4

Brand: Eaton Pages: 86

Brand: IEI Technology Pages: 136

Brand: Coby Pages: 1

Equinox SPR-E19-320-C-AC

Brand: SunPower Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands