Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 142 / 364

KNX control elements and application parameters

Control element "RTC control element"

Product manual 2CKA001473B5342

│

142

10.7.7 Display actual temperature

Options:

Deactivated

Activated

The parameter is used to specify whether the current temperature is displayed.

10.7.8 Display

Options:

Current setpoint

Relative set value

The parameter is used to specify the setpoint that is shown in the display.

10.7.9 Hide temperature unit

Options:

Disabled

Activated

The parameter is used to specify whether the temperature unit is displayed.

10.7.10 Unit of temperature

Options:

°C

°F

The parameter is used to specify the unit with which the temperature is displayed.

10.7.11 Adjusting the temperature unit via object

Options:

Disabled

Activated

The parameter is used to specify whether the adjustment of the temperature unit is made via an
object.

10.7.12 Heating/cooling switchover

Options:

Deactivated

Activated

The parameter is used to specify whether the RTC control element can be switched over
between heating and cooling mode.

10.7.13 Fan coil control during heating mode

Options:

Deactivated

Activated

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands