Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 205 / 364

KNX control elements and application parameters

Application "Fault and alarm messages" - Global settings

Product manual 2CKA001473B5342

│

205

10.18

Application "Fault and alarm messages" - Global settings

10.18.1 Use of fault and alarm messages

Options:

Deactivated

Activated

The parameter is used to specify whether the fault and alarm messages are displayed.

–

Disabled

: No display in the panel. No additional parameters available.

–

Activated

: The following parameters appear:

10.18.2 Page PIN-protected

Options:

Deactivated

Activated

The parameter is used to specify whether the fault and alarm messages application page is
protected by a PIN code.

–

Deactivated

: The application page is not protected.

–

Activated

: The application page can only be called up by entering a PIN code. The following

supplementary parameter is available:

PIN code level

Options:

Level 1

Level 2

Level 3

The parameter is used to specify the PIN code level for the application page.

Notice

Details about the PIN code, see chapter 9.6.1 “Basic settings (system
settings) of the panel“ on page 78.

10.18.3 Enable export

Options:

Deactivated

Activated

The parameter is used to specify whether the messages can be exported under the fixed file
name in CSV format. The messages can then be exported via the application page.

–

Deactivated

: No export. No additional parameters available.

–

Activated

: The following parameter appears:

File name [.CSV]

Options:

<Text>

The parameter is used to change the file name of the export file.

The length of the name is limited to 60 characters.

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands