Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 354 / 364

Operation

Product manual 2CKA001473B5342

│

354

12.7.12

Terminal resistor

Fig. 69:

Terminal resistor

In pure audio installations always set the terminal resistor [1] on "OFF". To do this, use switch 4
"RC".

In video installations or mixed audio and video installations set the terminal resistor for the last
devices of a branch on "ON".

12.7.13

Setting master/slave switches

Fig. 70:

Master/slave switches

One station "Master" must always be in each apartment. All other indoor stations in the same
apartment must be "Slave".

Indoor station that is set up as "Master":

1. Set switch 3 "M/S" [2] on "ON".

All other indoor stations:

1. Set switch 3 "M/S" [2] on "OFF".

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands