Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 199 / 364

KNX control elements and application parameters

Control element "Welcome control"

Product manual 2CKA001473B5342

│

199

10.16

Control element "Welcome control"

10.16.1 Name of the control element

Options:

<Name>

Naming of the control element for audio control.

The length of the name is limited to 36 characters.

10.16.2 Name of room (otional)

Options:

<Name>

Naming a room in which the control element Split Unit Control is located.

The length of the name is limited to 36 characters.

10.16.3 Size of the button

Options:

1x1

1x2

2x2

Specifies the size of the affected button on the dashboard.

10.16.4 Function icon

Options:

<Icon>

Specifies an icon for the function of the button.

10.16.5 Type of the control element

Options:

Outdoor station

Analogue camera

IP Camera

Specifying the control element type of the Welcome Control.

10.16.6 Using trigger object

Options:

Activated

Deactivated

The parameter is used to specify whether a trigger object is to be used for the activation.

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands