Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 127 / 364

background image

KNX control elements and application parameters

"Dimmer" control element

Product manual 2CKA001473B5342

│

127

Notice

The parameter can only be set when parameter "Icon type" is set on "User-
defined".

10.3.7 Status control element (icon) is controlled by a separate object

Options:

Deactivated

Activated

An additional 1-bit communication object "Status" is enabled via the parameter.

When the object has been enabled, the status display of the control element indicates the
current status of the object. The feedback object can ensure that the correct status is always
displayed.

If an actuator has a separate feedback object, this additional object can check whether the
actuator has switched. For this the feedback object of the actuator must be connected with the
feedback object of the button via a common group address (Action).

If the status display is not activated via a feedback object, the control element always changes
to the other status when actuated.

10.3.8 Manner of dimming

Options:

Start/stop

Stepwise

Value

–

Start/stop

: When the button is pressed a telegram with the information "dim brighter" or "dim

darker" is sent. When the button is released a telegram with the information "stop dimming"
is sent.

Brightness change [%]

:

Options:

Setting option in % (different values)

The parameter is used to specify in which step widths to dim.

Telegram is repeated every [sec.]

:

Options:

Setting option from 0.25 - 1.25 seconds

The parameter is used to specify the space of time between two dimming telegrams.

10.3.9 Enable 1-bit communication object "Disable"

Options:

Deactivated

Activated

There is the option of temporarily disabling the function via an additional communication object
"Disable".

«
...
125
126
127
128
129
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: GE Pages: 148

S-Class Excellent

Brand: Centrosolar Pages: 68

Individual 40 Compose Full-HD+

Brand: Loewe Pages: 60

Brand: Sonnenkraft Pages: 40

Brand: Q CELLS Pages: 11

NFC Code Touch Air

Brand: LOXONE Pages: 2

Brand: Quanmax Pages: 23

Brand: Epever Pages: 2

Brand: mikroElektronika Pages: 5

LCD3215 - MultiSync - 32" LCD Flat Panel Display

Brand: NEC Pages: 37

LCD4215 - MultiSync - 42" LCD Flat Panel Display

Brand: NEC Pages: 10

LCD3215 - MultiSync - 32" LCD Flat Panel Display

Brand: NEC Pages: 2

LCD4215 - MultiSync - 42" LCD Flat Panel Display

Brand: NEC Pages: 2

LCD3215 - MultiSync - 32" LCD Flat Panel Display

Brand: NEC Pages: 2

LCD3215 - MultiSync - 32" LCD Flat Panel Display

Brand: NEC Pages: 9

MultiSync V462-TM

Brand: NEC Pages: 2

Brand: Toshiba Pages: 22

Brand: Toshiba Pages: 182

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands