Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 192 / 364

KNX control elements and application parameters

Control element "Audio control"

Product manual 2CKA001473B5342

│

192

Options:

Deactivated

Activated

–

Deactivated

: No mute button is enabled. No additional parameters available.

–

Activated

: The mute button is enabled. The following supplementary parameter is available:

Object type mute

Options:

1 bit

1-byte value [0 - 255]

The parameter is used to specify the size of the communication object for sending
telegrams.

– 1

bit

: Commands of a mute button are sent with 1 bit (0 or 1). The following

supplementary parameters are available:

Value for mute

Options:

The parameter is used to send the command for "Mute" with "0" or "1".

Value for unmute

Options:

The parameter is used to send the command for "Unmute" with "0" or "1".

1-byte value [0 - 255]

: The value of a mute button is sent as 1-byte value without a sign.

The following supplementary parameters are available:

Value for mute

Options:

Setting option from 0 - 255

The parameter is used to send the value for "Mute" as absolute value.

Value for unmute

Options:

Setting option from 0 - 255

The parameter is used to send the value for "Unmute" as absolute value.

10.14.1 Use shuffle control

Options:

Deactivated

Activated

– Deactivated: No random playback is enabled. No additional parameters available.
– Activated: Random playback is enabled. The following supplementary parameter is

available:

Object type shuffle control

Options:

1 bit

1-byte value [0 - 255]

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands