manualshive.com logo in svg

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Introducing the Busch-Jaeger Busch-SmartTouch ST/A10.11-811, a cutting-edge device built to simplify your home automation experience. To unlock the full potential of this exceptional product, a comprehensive Product Manual is available for download - absolutely free! Access the manual today on manualshive.com, and discover the endless possibilities that await you.

Share
Download
background image

 

KNX control elements and application parameters

Application "Internal RTC"

 

 

 

 

Product manual 2CKA001473B5342 

│

277

 

 

10.24.141 

Settings of fan coil unit — Fan speed limit/level limit during Eco mode 

 

Options: 

Deactivated 

 

Activated 

This parameter limits the fan speed level when the system is switched to eco mode. 

 

10.24.142 

Fan settings heating  

 

 

Notice 

Only available when parameter "Number of fans" is set on "Heating/cooling via 
two systems". 

 

 

Notice 

Additional parameters for "Fan settings heating" are available under "Fan coil 
unit settings". 

 

10.24.143 

Fan settings cooling  

 

 

Notice 

Only available when parameter "Number of fans" is set on "Heating/cooling via 
two systems". 

 

 

Notice 

Additional parameters for "Fan settings cooling" are available under "Fan coil 
unit settings". 

 

10.24.144 

Fan settings - Level output 

 

Options: 

According to standard value table 

 

Specify individually 

This parameter is used to specify whether the level output is set according to the value table or 
individually. 

 

 

 

 

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

NEC LCD3215 - MultiSync - 32" LCD Flat Panel... Control Manual preview
LCD3215 - MultiSync - 32" LCD Flat Panel...
Brand: NEC Pages: 37
AMX AXD-CP4 Instruction Manual preview
AXD-CP4
Brand: AMX Pages: 66
Loewe Individual 40 Compose Full-HD+ Operating Instructions Manual preview
Individual 40 Compose Full-HD+
Brand: Loewe Pages: 60
Q CELLS Q.PEAK DUO-G10 Series Installation And Operation Manual preview
Q.PEAK DUO-G10 Series
Brand: Q CELLS Pages: 12
AXIOMTEK MPC103-845 User Manual preview
MPC103-845
Brand: AXIOMTEK Pages: 66
Redarc SMFB1160 Instruction Manual preview
SMFB1160
Brand: Redarc Pages: 16
M2I TOPRE Series Hardware Manual preview
TOPRE Series
Brand: M2I Pages: 20
Lenovo ThinkVision E2223s User Manual preview
ThinkVision E2223s
Brand: Lenovo Pages: 32
Advantech PPC-125 User Manual preview
PPC-125
Brand: Advantech Pages: 60
Sony PFM-42B2 Operating Instructions Manual preview
PFM-42B2
Brand: Sony Pages: 294
Sony PFM-42X1N Operating Instructions Manual preview
PFM-42X1N
Brand: Sony Pages: 376
Sony KDL-26M4000/W - Bravia M Series Lcd Television Specifications preview
KDL-26M4000/W - Bravia M Series Lcd Television
Brand: Sony Pages: 2
Sony KDL-26ML130 - 26" Bravia M-series Digital Lcd Television Specifications preview
KDL-26ML130 - 26" Bravia M-series Digital Lcd Television
Brand: Sony Pages: 2
Sony KDL-26M4000/T - Bravia M Series Lcd Television Specifications preview
KDL-26M4000/T - Bravia M Series Lcd Television
Brand: Sony Pages: 2
Sony KDL-26M4000/R - Bravia M Series Lcd Television Important Safety Instructions preview
KDL-26M4000/R - Bravia M Series Lcd Television
Brand: Sony Pages: 2
Sony KDL-26M4000/R - Bravia M Series Lcd Television Specifications preview
KDL-26M4000/R - Bravia M Series Lcd Television
Brand: Sony Pages: 2
Sony KDL-26N4000 - 26" LCD TV Brochure preview
KDL-26N4000 - 26" LCD TV
Brand: Sony Pages: 6
Sony KDL-26M3000 - 26" Bravia M-series Digital Lcd Television Specifications preview
KDL-26M3000 - 26" Bravia M-series Digital Lcd Television
Brand: Sony Pages: 2

Brands by name

Popular brands

Load more brands